Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
• Do not operate if fuel has been spilled. Instead, move the machine to a different location and avoid creating sparks. • The machine has hot surfaces which can cause burns. Operate the unit in a safe environment and away from children. • Do not touch hot surfaces or allow accessories to contact hot surfaces. 4 English • Do not allow the high pressure hose • Avoid tipping the machine on its to come into contact with the muffler side. guard. SAVE THESE INSTRUCTIONS • Do not leave the machine running unattended. WATER SUPPLY (Cold Water Only) . CAUTION When connecting the water inlet to the water supply mains, local regulations of your water company must be observed. In some areas the unit must not be connected directly to the public drinking water supply. This is to ensure that there is no feedback of chemicals into the water supply. Direct connection via a receiver tank or backflow preventer, for example, is permitted. Dirt in the feed water will damage the unit. To avoid this risk, we recommend fitting a water filter. • Garden hose must be at least 5/8 inch in diameter. • Flow rate of water supply must not fall below 2.8 GPM (gallons per minute). • Flow rate can be determined by running the water for one minute into an empty 5-gallon container. • The water supply temperature must not exceed 104°F/40°C. • Never use the pressure washer to draw in water contaminated with solvents, e.g. paint thinners, gasoline, oil, etc. • Always prevent debris from being drawn into the unit by using a clean water source. Use additional water filter. • Do not operate pressure washer without the water turned on. English 5 6 English .. STEP 1: Attach the handle to the frame of the pressure washer. Align holes, insert bolts, and tighten with knobs. .. STEP 2: Mount the gun/hose storage handle. .. STEP 3: Mount the nozzle holder with enclosed nylon rivets to the handle. .. STEP 4: Place the quick connect nozzles in the nozzle holder. .. STEP 5: Attach the wand to the spray gun. .. STEP 6: Pull the spring-loaded collar of the wand back to insert your choice of quick connect nozzle. .. STEP 7: Release the collar and push the nozzle until the collar clicks. WARNING High pressure in nozzle area. Risk of injury caused by improperly locked nozzle. .. Make sure you hear a ‘click’ when inserting the nozzle tip into the wand. .. Pull the nozzle to make sure it is seated properly before operating your unit. ASSEMBLY INSTRUCTIONS • STEP 8: Attach the high pressure hose to the spray gun. ..STEP 6: OPERATING INSTRUCTIONS CAUTION Do not run the engine with a high or low oil level as this can cause engine damage. If you have further questions regarding the engine, please refer to the engine manual included with the unit. • STEP 1: Check oil level. Oil level should always be between the “FULL” and “ADD” marks on the dipstick. Be sure the machine is level when checking the oil level. (Refer to the engine’s operating manual for seasonal grades.). We recommend that the oil be changed after the first 5 hours of use, then once every 25 hours. • STEP 2: Fill gas tank with unleaded gasoline. Do not use leaded gasoline. Do not add oil to the gasoline. • STEP 3: Connect the high pressure hose to the unit’s high pressure outlet. • STEP 4: Connect garden hose to unit’s water inlet. • STEP 5: Connect garden hose to the cold water source and turn water on completely. Do not use hot water. Unlock the trigger gun safety lock. Trigger the gun to eliminate trapped air, wait for a steady flow of water to emerge from the spray nozzle. • STEP 7: Pull the choke rod to the CLOSED position. Starting a Warm engine: If the engine has run out of fuel, set choke rod to the CLOSED position after refueling. If the engine has not run out of fuel, leave the choke rod in the OPEN position. • STEP 8: Engine with manual throttle: Slide the throttle lever away from the SLOW position, about 1/3 of the way toward the FAST position. Engine with fixed throttle: Move the engine stop switch to the ON position. For engine details see engine manual. • STEP 9: Pull the starter handle. If the engine fails to start after 3 pulls, squeeze the trigger gun to release pressure, and repeat step. After the engine warms up enough to run smoothly, move choke rod to OPEN position and throttle to FAST position. English 7 USING THE ACCESSORIES USING THE ACCESSORIES Quick connect nozzles 0° spray angle = Red nozzle For particularly stubborn accumulation of grime. Not recommended for soft materials like sidings, decks, painted surfaces, cars. 15° spray angle = yellow nozzle For dirt accumulation over a surface. 25° spray angle = Green nozzle For dirt accumulation over a large surface. 40° spray angle = White nozzle For moderate dirt accumulation over a large surface. High pressure in nozzle area. Risk of injury caused by improperly locked nozzle. • Make sure you hear a ‘click’ when inserting the nozzle tip into the wand. • Pull the nozzle to make sure it is seated properly before operating your unit. (...
Other models in this manual:Pressure Washers - G 3025 OH (3.03 mb)