Votes - 2, Average rating: 3
(
)
)
|
manual abstract
• If engine does not start after two pulls, squeeze trigger of gun to relieve pump pressure. Pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury. • Keep children away from the pressure washer at all times. • Do not overreach or stand on an unstable support. • Do not use pressure washer while standing on a ladder. • Grip gun/wand firmly with both hands. Expect the gun to kickback when triggered. DANGeR: RISk of INjuRy oR PRoPeRty DAmAGe WheN tRANSPoRtING oR StoRING What can happen • Fuel or oil can leak or spill and could result in fire or breathing hazard. Serious injury or death can result. Fuel or oil leaks will damage carpet, paint or other surfaces in vehicles or trailers. How to prevent it • If pressure washer is equipped with a fuel shut-off valve, turn the valve to the OFF position before transporting to avoid fuel leaks. If pressure washer is not equipped with a fuel shut-off valve, drain the fuel from tank before transporting. Only transport fuel in an OSHA-approved container. Always place pressure washer on a protective mat when transporting to protect against damage to vehicle from leaks. Remove pressure washer from vehicle immediately upon arrival at your destination. English 7 EnglishEnglish WARNING: RISk of hot SuRfAceS WARNING: RISk of BuRStING What can happen How to prevent it What can happen How to prevent it • Over inflation of tires could result in serious injury and property damage. • High-velocity fluid spray directed at pneumatic tire sidewalls (such as found on automobiles, trailers and the like) could damage the sidewall resulting in serious injury. • Use a tire pressure gauge to check the tires pressure before each use and while inflating tires; see the tire sidewall for the correct tire pressure. note: Air tanks, compressors and similar equipment used to inflate tires can fill small tires similar to these very rapidly. Adjust pressure regulator on air supply to no more than the rating of the tire pressure. Add air in small increments and frequently use the tire gauge to prevent over inflation. • On pressure washers rated above 1600 PSI (11032 kPa) use the widest fan spray (40. nozzle) and keep the spray a minimum of 8" (20 cm) from the pneumatic tire sidewall. Do not aim spray directly at the joint between the tire and rim. • Contact with hot surfaces, such as engines exhaust components, could result in serious burn. • During operation, touch only the control surfaces of the pressure washer. Keep children away from the pressure washer at all times. They may not be able to recognize the hazards of this product. WARNING: RISk of chemIcAl BuRN What can happen • Use of acids, toxic or corrosive chemicals, poisons, insecticides, or any kind of flammable solvent with this product could result in serious injury or death. How to prevent it • Do not spray acids, gasoline, kerosene, or any other flammable materials with this product. Use only household detergents, cleaners and degreasers recommended for use with pressure washers. • Wear protective clothing to protect eyes and skin from contact with sprayed materials. 8 WARNING: RISk of electRI cAl Shock What can happen How to prevent it • Spray directed at electrical • Unplug any electrically outlets or switches, or objects operated product before connected to an electrical attempting to clean it. Direct circuit, could result in a spray away from electric fatal electrical shock. outlets and switches. WARNING: RISk of INjuRy fRom lIftING What can happen How to prevent it • Serious injury can result • The pressure washer is too from attempting to lift too heavy to be lifted by one heavy an object. person. Obtain assistance from others before lifting. Save theSe inStructionS For Future uSe inStaLLation Pressure Washer Assembly (Fig. 1) 1. Place handle assembly (O) onto frame, depress the snap buttons, and slide the handle assembly onto the frame (F) until snap buttons are secured in place. cAutIoN: Risk of personal injury. Avoid placing hands between handle and frame when assembling to prevent pinching. F O 2. Attach high-pressure hose (P) to spray gun. Make sure it is secure. 3. Connect wand (E) to spray gun. Make sure connection is secure. E P 4. Thread the side handle (D) into spray gun extension and tighten to desired position. 5. Place the nozzle holder (B) onto the panel assembly (A) and push each nozzle holder into place. 6. Remove the five colored quick-connect nozzles from the plastic bag and insert them into correct grommet on the nozzle holder. Nozzles are color coded to match colored nozzles on panel assembly. B A English D 9 EnglishEnglish note: The high pressure pump is maintenance free and requires no oil, if there is a problem with the pump contact a DeWALT factory service center, a DeWALT authorized service center or other qualified service personnel. WARNING: Risk of bursting. Use a tire pressure gauge to check the tires pressure before each use and while i...