Votes - 3, Average rating: 3.7 ( )

Manafacture: Graco Inc. File size: 968.22 kb File name: 4646738b-b88f-4070-90cf-e9d2b4c5e222.pdf Language of manual:

GRACO INC. RO.Box 1441 MINNEAPOLIS, MN 55440-1441 @COPYRIGHT1991, GRAGO INC. HIGH PRESSURE SPRAY CAN CAUSE SERIOUS INJURY FOR PROFESSIONAL USE ONLY. OBSERVE ALL WARNINGS. Read and understand all instruction manuals before operating equipment. FLUID INJECTION HAZARD General Safetymis pressure washer generates very high fluid pressure. Spray from the gun, leaks or ruptured components can inject fluid through your skin and into your body and cause extremely serious bodily injury including the need for amputation. Also,fluid injectedorsplashed into the eyes or on the skincan cause serious damage. NNER point the spray gun or wand at anyone or at any part of the body.NNER put hand or fingers over the spray tip. ALWAYSfollow the Pressure Relief Procedure, before cleaning or servicing any part of the sprayer. NNER try to stop or deflect leaks with your hand or body. Be sure equipment safety devices are operatingproperly before eachuse. Medical Treatment If any fluid appears to penetrate your skin, getEMERGENCY MEDICALTREATMENTATONCE.DO NOT TREATAS A SIMPLE CUT. Tell the doctor exactlywhat fluid was injected. NOTE TO PHYSICIAN lnjection inthe skin is a traumatic injur,! It Is Important to treat the injury surglcaily as soon as possible. Do not delay treatment to research toxicity Toxicity is a concern with some exotic coatings injected direct& into the bloodstream. Consultationwith a plastic surgeon or reconstructivehandsurgeon may be advisable. Pressure Relief Procedure To reduce the risk of serious bodily injury, including fluid injection and splashing in the eyes or on the skin, always follow this procedure whenever you stopspraying for more than 10minutes, when shutting down, and before checking01 repairing any partofthe system. 1. Engage the trigger safety latch. 2. Tum the sprayer off. 3. Disconnect the electrical supply. 4. Shut off the water supply. 5. Disengage the trigger safety latch and trigger the gunio relieve pressure, and then engage the triggersafety latch again. 6. Before long-term (overnight) storage, disconnect the water supply and disconnect the electricity. Spray Gun Safety Devices Be sure all gun safety devices are operating properlybefore each use.Do not remove or modify any part of the gun; this can cause a malfunction and result in serious bodily injury. SAFETY LATCH: Whenever you stop spraying for a moment, always set the gun Safety latch inthe engagedor "safe" position, making the gun inoperative. Failureto properly set the safety latch can result in accidental triggering of the gun. SPRAY TIP SAFEPI: Use extreme caution when cleaning or changing spray tips. Ifa spray tip clogs while spraying, engage the gun safety latch immediately. ALWAYS follow the Pressure Rellet Procedure and then remove the spray tip to clean it. GROUNDING INSTRUCTIONS 1-malfunctionIf it should must be grounded. mis Droduct DANGER or bieak down, grounding provides a path of least improper connectionof the equipment-groundingresistance for electric current to reduce the risk of conductor can result In the risk of electrocution. electric shock. This equipmentis equipped with a cord Check with a qualified electrician or service having an equipment-grounding conductor and a personif you are in doubt as to whether the outlet grounding plug. The plug must be plugged into an Is properly grounded. aooromiate outlet that is DroDerlv installed and giunded in accordance with ail lbcal codes and ordinances. GROUND FAULT CIRCUIT INTERRUPTER PROTECTION To comply with the National Electrical Code (NFPA 70) and to provide additional protection from the riskof electric shock, connect this pressure washer to a circuit that is protected by a ground-fauit circuit-intempter(GFCI). EQUIPMENT MISUSE HAZARD General Safety Any misuse of the pressure washer or accessories, such as overpressurizing, modifying parts, usingincompatible chemicals and fluids,or using wom or damaged parts, can cause them to rupture and resun in fluid injection, splashing in the eyes or on the skin, or other serious bodily injury, fire, explosion or propertydamage. NEVER alter or modify any part of this equipment; doing so could cause it to malfunction. CHECK ail spray equipment regularly and repair or replace wom or damaged parts immediately. ALWAYS wear protective eyewear and appropriateclothing. Ifusing a chemical injector, read and follow the chemical manufacturer’s literature for recommendations on additional protective equipment, such as a respirator, System Pressure This sprayer can develop high operating pressure. Be sure that all spray equipment and accessories are rated to withstand the maximum working pressure of this sprayer. DO NOT exceed the maximum working pressure of any component or accessory usedin the .. system. Chemical Compatibility BE SURE that ail chemicals used in the chemical injector are compatible with the wetted parts of the hose, gun, wand and tip, as giveninthe Technical Data (inside back cover). Always read the chemical manufacturer’s...

Download now

Please, enter two numbers from picture: