Login:
Votes - 3, Average rating: 4 ( )

User manual Nilfisk-ALTO, model A08058-0412-0

Manafacture: Nilfisk-ALTO
File size: 2 mb
File name: 66a2fa64-e62a-4b6a-a450-c660544d86e4.pdf
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


• High velocity fluid spray can cause objects to break, propelling particles at high speed. • Light or unsecured objects can become hazardous projectiles. CARTON CONTENTS Operation Manual Nozzle Cleaning Tool Chemical Hose Nozzle Holder Quick Connect Nozzles Formed Rubber Covers Engine Manual Knobs Engine Frame and Wheel Assembly Registration card Saddle Bolts Bagged Parts Tube Bracket Handle Engine Oil Hose Reel with parts bag Spray Gun High Pressure Hose Quick Connect Spray Wand ASSEMBLY INSTRUCTIONS 2. Connect tube bracket (b) to frame using the hardware (c) supplied. 1. Place handle assembly onto frame, depress the snap buttons, and slide the handle assembly onto the frame until snap buttons snap into place. b c 3. Assembly hose reel. a. Attach handle to flange assembly. NOTE: Screws must be inserted from the inside of hose reel and secured with nuts on the outside as shown. Tighten securely. b. Bolt hose reel to reel bracket as shown. Tighten securely. c. Apply sealant tape to swivel end of high pressure hose. d. Feed high pressure hose through slot (1) in flange assembly and connect to swivel (2). Tighten securely. e. Make a loop in hose as shown. Place hose into hose clamp (3), squeeze hose clamp together, slide onto long screw post, and secure with nut (4). Tighten securely. NOTE: Do not overbend or kink hose. f. Turn handle and reel hose onto reel. g. Attach hose reel inlet to high pressure pump. 3 4 hose end with swivel 1 Do not operate this hose reel until you have read and understood the Pressure Washer Owners Manual for Safety, Operation, and Maintenance Instructions. 2 4. Attach high pressure hose to gun. Tighten securely. 9. Add engine oil (supplied) to engine. Refer to Engine Owners Manual supplied by engine manufacturer for correct procedure. NOTE: There will be a slight amount of oil in the engine from factory testing. 5. Connect wand to gun. Tighten securely. NOTE: The high pressure pump was filled with oil at the factory. There is no need to add oil at this time, see the Maintenance section of this manual for Maintenance information. 6. Place the nozzle holder onto the panel (located on the handle assembly) and push each nozzle holder into place. 7. Remove five colored quick connect nozzles from plastic bag and insert them into correct grommet on the nozzle holder. NOTE: Nozzles are color coded to match colored nozzles on panel. The shipping plug must be removed and replaced with the dipstick/oil plug before operating pressure washer. 10. Using a 7/8" wrench, remove shipping plug from pump by turning it counterclockwise. Discard plug. 11. Remove dipstick/oil plug from plastic bag and install into pump, tighten securely. 8. Slide the formed rubber covers onto the handle's on-board hose and wand storage. OPERATING INSTRUCTIONS Compare the illustrations with your unit to familiarize yourself with the location of various controls and adjustments. Save this manual for future reference. High Pressure Hose Engine Spray Gun Quick Conn...

Other models in this manual:
Pressure Washers - A08058-0412-0 (2 mb)
Pressure Washers - A08058-0412-0 (2 mb)
Pressure Washers - A08058-0412-0 (2 mb)
Pressure Washers - A08058-0412-0 (2 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category