Votes - 3, Average rating: 4
(
)
)
|
manual abstract
• Disconnect the high pressure hose and the garden hose. 5.6 HOSE REEL KIT Insert the high pressure hose nut coupler (Fig.24) into the slot in the hose reel. Hold the hose firmly into the slot. At the same time, turn handle in the direction shown (Fig. 25). Allow hose to slide through hand applying slight resistance for proper coiling. Stop winding hose 2 ft. (60 cm) from gun to provide enough slack to store gun in holder located on the docking station. See page 6, #27 for storage location. 16 English 6.0 MAINTENANCE 6.1 CONNECTIONS Connections on pressure washer hoses, gun and spray wand should be cleaned regularly and lubricated with light oil or non-water soluble grease to prevent leakage and damage to the o-rings. 6.2 NOZZLE Clogging of the nozzle causes the pump pressure to be too high and cleaning is immediately required. 1. Clear the nozzle by forcing a stiff wire through center hole. 2. Backflush the nozzle with water. 3. Reconnect the nozzle to the wand. 6.3 LUBRICATION The pressure washer is designed with a permanent lubrication system. Conventional oil check and oil changes are not necessary. NOTE: IN CASE OF OIL LEAKAGE, CONTACT THE CUSTOMER SERVICE DEPARTMENT CONCERNING REPAIR. A SMALL AMOUNT OF OIL LEAKAGE IS NORMAL. 6.4 WATER SCREEN The pressure washer is equipped with a water inlet screen filter to protect the pump. CAUTION: If the screen is not kept clean, the flow of water to the pressure washer will be restricted and the pump may be CAUTION damaged. • To clean inner water screen, remove the inlet nipple and remove the filter screen from the inlet. • Backflush screen to clean. • Replace screen and inlet nipple immediately to prevent any foreign matter from entering the pump. CAUTION: Do not damage the screen while removing or cleaning. Any foreign particles entering the pump may damage CAUTION the pump. 6.5 COOLING SYSTEM The air vents, located in and around the pressure washer, must be kept clean and free of any obstructions to ensure proper air cooling of the motor during operation. WARNING: Prevent water from penetrating the vents of the pressure washer to minimize the risk of damage to the WARNINGmachine and to reduce the risk of shock to the operator. 7.0 SERVICING A DOUBLE- INSULATED APPLIANCE In a double-insulated product, two systems of insulation are provided instead of grounding. No grounding means is provided on a double-insulated product, nor should a means for grounding be added to the pressure washer. Servicing a double-insulated product requires extreme care and knowledge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated product must be identical to the parts they replace. A double- insulated product is marked with the words “DOUBLEINSULATION” or “DOUBLE-INSULATED”. The symbol above may also be marked on the product. 17 English 8.0 TROUBLESHOOTING PROBLEM OR CONCERN POSSIBLE CAUSE SOLUTION Detergent is not dispensing Detergent suction tube has been disconnected or clogged. Remove the soap lance assembly from the detergent bottle. Make sure that the clear tube is properly connected to the soap lance. If it is not connected then reconnect it. Detergent to Water ratio Your Powerwasher draws detergent at a 10:1 ratio. Most pressure washer detergents are generally concentrated within that range so minimal adjustment is required. If you feel like you are using more detergent than is required for the application you can dilute it with regular tap water. Detergent - What to use We recommend that you use a cleaner which is specifically designed for power washers. There are different kinds available depending on the application. Check with your local Home Depot store for the product which is best suited for your needs. Never use Bleach, Ammonia or Hot water in the unit. Circuit breaker trips or Fuse blown in Fuse Box Circuit overload Check that the circuit is rated at 15 amps or greater. Make sure the unit is plugged into a dedicated circuit. Extension cord too long or wire size too small Use proper extension cord as recommended in owner’s manual. Nozzle partially blocked Clean Nozzle as instructed in section 6.2. Excessive pressure Clean Nozzle as instructed in section 6.2 GFCI Plug installation GFCI Plug malfunction For GFCI reset procedures see owner’s manual section 4.3. For instructions regarding the GFCI Plug installation or malfunction please email us directly at customerservice@huskypowe rwasher.com. Gun/Hose - Leaking water Gun/Hose will need to be replaced. Replacement parts are not available for the Gun/Hose. Email us at customerservice@huskypow erwasher.com for assistance or order online at Leaking Oil from Pump A small amount of leakage is normal If leakage occurs please contact us directly at custo merservice@huskypowerwasher.com. Leaking water from bottom of unit Machine Inlet connection is defective Check the Machine Inlet at the back of the unit to ensure ...
Other models in this manual:Pressure Washers - HD1500 (11.73 mb)