Votes - 3, Average rating: 4
(
)
)
|
manual abstract
NOTE: CONNECTING A LINE LEVEL DEVICE TO A PH INPUT MAY CAUSE THAT MIXER CHANNEL TO OVERLOAD AND OR DISTORT. GROUNDING SCREW When using (a) turntable(s), you will need to ground the RCA cable(s) by screwing in the grounding fork(s) to the GROUNDING SCREW located on the rear panel of the MM-4000 mixer. Attach a PHONO (Turntable) ground line to the silver GROUND THUMB SCREW that is situated at the bottom middle of the rear panel. MIC (MICROPHONE) INPUTS The MM-4000 has 5 MIC (MICROPHONE) inputs 1 main mic input located on the top panel, which is controlled by its own volume rotary, and four auxiliary MIC inputs located on the back panel. The AUX MIC inputs are controlled by thier corresponding channels fader, when that channels selector switch (12) is set to the MIC position. HEADPHONE OUTPUT The HEADPHONE OUTPUT located at the front bottom right hand corner of the MM-4000 will accept any headphone with a standard 1/4” connector and or adapter and will allow you to CUE your music program before you play it, you can adjust the volume and PGM mix of the HEADPHONE (see CONTROLS). Then when all of your connections have been made turn on the mixer by pressing the POWER SWITCH. MICROPHONE VOLUME Allows you to adjust the volume of the microphone signal for MIC input (1) which is located above this volume rotary (see above) . MICROPHONE EQ and TALKOVER SWITCH The MICROPHONE EQ Let’s you to control the low frequency and the high frequency of the microphone signal.The TALKOVER switch allows you to quickly attenuate the main output so the microphone can be heard over the main music program. MIXER CHANNELS (NOTE: ALL 4 CHANNELS HAVE THE SAME FEATURES) CHANNEL INPUT SELECTOR The CHANNEL INPUT SELECTOR switches allow you to choose which input will be controlled by that channels corresponding volume FADER. For example on CHANNEL (1) the INPUT SELECTOR allows you to choose between PHONO 1,LINE 1 and MIC 2 , and also on CHANNEL (2) you can switch between PHONO 2, LINE 2 and MIC 3 and on CHANNEL (3) you can select either LINE 3,LINE 4 or MIC 4 input, then on CHANNEL (4) you can choose between LINE 5, LINE 6 and MIC 5. CHANNEL ROTARY GAIN The CHANNEL ROTARY GAIN allows you to boost the signal of each individual channel depending on how low or high its input level is. 9 MM-4000 5 13 PRECAUTIONS: 1. All instructions should be read before using this equipment. 2. To reduce the risk of electrical shock, do not open the unit. Please refer all servicing needs to a Gemini-qualified service technician. 3. Do not expose this unit to direct sunlight or a heat source such as a radiator or stove. 4. This unit should be cleaned only with a damp cloth. Avoid solvents or other cleaning detergents. 5. When moving this equipment it should be placed in its original carton and packaging. This will reduce the risk of damage during transit. 6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. 7. DO NOT USE SPRAY CLEANERS OR LUBRICANTS ON CONTROLS, SURFACES OR SWITCHES. IN THE USA ~ IF YOU EXPERIENCE PROBLEMS WITH THIS UNIT CALL GEMINI CUSTOMER SERVICE AT: 1 (732) 346-0061. DO NOT ATTEMPT TO RETURN THIS EQUIPMENT TO YOUR DEALER. CONTROLS: (CONTINUED) 18 21 22 3 BAND EQUALIZER The 3 BAND EQUALIZER adjust the tone of each CHANNEL by giving you a choice 3 frequencies (BANDS) to adjust , from LOW, MIDRANGE (MID) and HIGH’s ,you can use the adjustment knobs to higher or lower the 3 separate frequencies till the sound of the music program is appropriate for your listening environment. EFFECT ASSIGN The EFFECT ASSIGN buttons allow you to choose which channel (LINE or MIC) will be sent to the effects section, either one or all channels can be selected at once (see effects section). CHANNEL CUE SELECTOR The CHANNEL CUE SELECTOR allows you to choose which channel will be heard in the headphones, one or all can be pressed at the same time, when pressed a red LED will illuminate indicating the CUE is in the ON position CHANNEL VOLUME FADER After you have chosen which input you will use with the INPUT SELECTOR the corresponding CHANNEL FADER will allow you to adjust the volume for that particular CHANNEL. CROSSFADER ASSIGNMENT The fader assignment rotary allows you to assign which two of the 4 channels will be controlled by the CROSSFADER.There are 5 selections for either side of the CROSSFADER which can be either CHANNEL 1,2,3,4 or OFF, In the OFF position the CROSSFADER will not affect the volume of any CHANNEL. CROSSFADER The CROSSFADER allows you to mix evenly from one source to another. On the MM-4000 The CROSSFADER is assignable between either channels (1) and (2) or channels (3) and (4) depending on the position of the fader assignment push button (see above). The CROSS FADER on the MM-4000 is also removable and if the need arises can be replaced.The RG-45 (RAILGLIDE™) DUAL-RAIL CROSS FADER, which has internal dual stainless steel rails that allow the slider to ride smoothly and accurately from end to end can be purchased from your local GEMINI dealer. NOTE: WH...
Other models in this manual:Mixers - MM-4000 (3.23 mb)