Votes - 4, Average rating: 4.3
(
)
)
|
manual abstract
Note that the back tube extension of the lower leg frame is longer than the front 3. Align holes in upper and lower frames at desired height' insert height adjustment rod "K", and secure with adjustment knob. Repeat for left and right frames. IMPORTANT:It is best to set the proper height at this time. Use chart below as a guideline to determine height adjustment positions. HEIGHT ADJUSTMENT GUIDELINES Page 3 I ■ If 111111111111111111111111111 * 11111111 j11111111 0" I" 2" 3" 4. Attach back cross bar "E" to left leg frame using 2 1/4" bolt "NT. 5. Attach footrest bar "D" to left leg frame using 2 1/4" bolt "N". 6. Attach upper cross tube-small "G" to left leg frame using 2 1/4" bolt "N". 7. Repeat steps above to attach all 3 cross pieces to right leg frame. Be certain that all 6 bolts are tightened securely to ensure stalility of table. 8. Choose either casters "L" or floor glides "L" and screw into holes in bottom of lower leg tubes. Page 4 | ! ||i j i j i | : | f| i I « | « | r | r | * j i p i « | ; 1 ' | r Ï 1 j 0" I" 2" 3" 9. Attach all 4 drawer support tubes and hangers "H" to the upper leg frames using 2 1/4" bolts "N" and nylon washers "T" ( Be sure that nylon washer is positioned between hanger & leg frame ) on the inside and 5/8" bolts "P" on the outside. Page 5 □ // TT*pTrTrTTJrT TT'TT'TTl J 'I" J11 'j'l ' j11 |1 r I t | V // 0 1' 10. Attach upper cross bar-large "F" to front of upper leg frames using 1 1/2" bolts "0". 11. Attach tilt mechanisms "I" to back of upper leg frames using 1 3/8" bolts "Y", nylon washers "T" and nuts "S". For ease of handling keep mechanisms in folded position for time being with elastic bands. Pay close attention to the correct orientation of the mechanisms and be sure that nylon washer "T" is positioned between mechanism and leg frame. Tighten nut "S" securely. It has a built-in locking ring and you may prefer using a standard wrench or pliers to drive the bolt all the way through the unt. 12. Base assembly is now complete. Set aside. Right I Page 6 r If r 11 ' 111 ' 1.1 ', ' 1111 1 I ‘ | 1 1 1 | i I I | I'H 11 ■ i • i • j 0" r 2" 3" 13. Place table top "A" on a carpeted or otherwise protected floor, to avoid scratches, with the pre-drilled holes facing up. 14. Choose either the pencil ledge "U" or pencil tray "V" ( not both ) and attach using 5/8" Phillips screws "R" into pre-drilled holes in front of tabletop. If attaching metal pencil ledge, folded-over edge should be on the underside ( unfinished side ) of tabletop and should point towards back edge of board. Figure 5 Pencil Tray Figure 6 Pencil Ledge Page 7 I ■ If 111111111111111111111111111‘11111111111111111 0" I" 2" 3" 15. Carefully turn base assembly upside down and place on table top (this may require two people ) Be sure that the two threaded inserts near the back edge of the table top align with the attachment holes in the tilt mechanisms "I" and the base is centered left-to-right. The upper cross bar-large "...
Other models in this manual:Furniture - CraftMaster CM40-4-WB (1.09 mb)
Furniture - CraftMaster CM40-4-XB (1.09 mb)