2E8/IRQ3 Enable onboard Serial port 2 and address is 2E8. Disabled Disable onboard Serial port 2. • UART2 Mode Select (This item allows you to determine which UART2 Mode of onboard I/O chip), the default value is Normal. ASKIR Set onboard I/O chip UART2 to ASKIR Mode. IrDA Set onboard I/O chip UART2 to IrDA Mode. Normal Set onboard I/O chip UART2 to Normal Mode. • UART2 Duplex Mode The default value is Half. Half Set UART2 Duplex Mode to Half. Full Set UART2 Duplex Mode to Full. 4-23 6VA7+ • RxD , TxD Active The default value is Hi, Lo. Hi, Hi RxD set Hi, TxD set Hi. Hi, Lo RxD set Hi, TxD set Lo. Lo, Hi RxD set Lo,TxD set Hi. Lo, Lo RxD set Lo,TxD set Lo. • IR Transmittiion delay The default value is Enabled. Enabled Set IR Transmittiion delay Enabled. Disabled Set IR Transmittiion delay Disabled. • Onboard Parallel port The default value is 378/IRQ7. 378/IRQ7 Enable onboard LPT port and address is 378/IRQ7. 278/IRQ5 Enable onboard LPT port and address is 278/IRQ5. Disabled Disable onboard LPT port. 3BC/IRQ7 Enable onboard LPT port and address is 3BC/IRQ7. • Parallel Port Mode The default value is SPP. SPP Using Parallel port as Standard Parallel Port. EPP Using Parallel port as Enhanced Parallel Port. ECP Using Parallel port as Extended Capabilities Port. ECP/EPP Using Parallel port as ECP/EPP mode. • PS/2 Mouse Power on The default value is Disabled. Disabled Disable PS/2 Mouse Power on . Left Double Double Click on PS/2 mouse left button to Power on system. Right Double Double Click on PS/2 mouse right button to Power on system. 4-24 BIOS Configuration • Keyboard Power on The default value is POWER Key. Disabled Disable Keyboard Power on . Multikey Enter multikey combination to Power on system. POWER Key If your keyboard have “POWER Key” button, you can press the key to power on your system. • KB Power ON Password Enter Enter from 1 to 5 characters to set the Keyboard Power On Password. You can power on your system by entering password from the Keyboard after setting the “Keyboard power on” jumper (JP1) and password in CMOS Setup. 4-25 6VA7+ 4.13. SUPERVISOR / USER PASSWORD When you select this function, the following message will appear at the center of the screen to assist you in creating a password. Figure 4.10: Password Setting Type the password, up to eight characters, and press . The password typed now will clear the previously entered password from CMOS memory. You will be asked to confirm the password. Type the password again and press . To disable password, just press when you are prompted to enter password. A message “PASSWORD DISABLED” will appear to confirm the password being disabled. Once the password is disabled, the system will boot and you can enter Setup freely. If you select System at Security Option in BIOS Features Setup Menu, you will be prompted for the password every time the system is rebooted or any time you try to enter Setup Menu. If you select Setup at Security Option in BIOS Features Setup Menu, you will be prompted only when you try to enter Setup. 4-26 BIOS Configuration 4.14. IDE HDD AUTO DETECTION Figure 4.11: IDE HDD Auto Detection Type "Y" will accept the H.D.D. parameter reported by BIOS. Type "N" will keep the old H.D.D. parameter setup. If the hard disk cylinder number is over 1024, then the user can select LBA mode or LARGER mode for DOS partition larger than 528 MB. 4-27 6VA7+ 4.15. SAVE & EXIT SETUP Figure 4.12: Save & Exit Setup Type "Y" will quit the Setup Utility and save the user setup value to RTC CMOS. Type "N" will return to Setup Utility. 4-28 BIOS Configuration 4.16. EXIT WITHOUT SAVING Figure 4.13: Exit Without Saving Type "Y" will quit the Setup Utility without saving to RTC CMOS. Type "N" will return to Setup Utility. 4-29 6VA7+ Appendix A: VIA Chipsets Driver Installation a. VIA 4 in 1 Service Pack Utility: Insert the support CD that came with your motherboard into your CD-ROMdriver or double –click the CD driver icon in My Computer to bring up the screen. 1.Click “VIA 4in 1 Service Pack Utility” item. (1) (2) (3) (4) 2.Click “Next”. 3.Click “Yes”. 4.Click “Next”. 5.Click “Next”. (5) (6) A-1 Appendix 6.Click “Next”. 7.Click “Next”. (7) (8) 9.Click “Next”. (9) (10) 8.Click “Next”. (11) (12) 10.Click “Finish” to restart computer. A-2 6VA7+ Appendix B: Bugs & Limitations 1. For some SDRAM Modules, when you are running Winstone 99 (Business Winstone 99) under the Windows NT4.0 operating system, the following error message may appear: “ mtrun-exe-Bad image: The application or DLL C:\ WINNT \ System \ MSVCRi40.DLL is not a valid Windows NT image. Please check this against your installation diskette.” B-1 Appendix Appendix C: BIOS Flash Procedure BIOS update procedure: • Please check your BIOS vendor (AMI or AWARD) on the motherboard. • It is recommended you copy the AWDFlash.exe or AMIFlash.exe in driver CD (D:\>Utility\BIOSFlash) and the BIOS binary files into the directory you made in your hard disk..i.e:C:\>Utility\ (C:\>Utility :...
