Votes - 0, Average rating: 0
(
)
)
|
manual abstract
-27 -BIOS Setup English EnglishEnglish • Floppy 3 Mode S upport (for J apan Area) 8Disabled Normal Floppy Driv e. (Default v alue) 8Driv e A Driv e A is 3 mode Floppy Driv e. 8Driv e B Driv e B is 3 mode Floppy Driv e. 8Both Driv e A & B are 3 mode Floppy Driv es. CHalt on The category determines w hether the computer w ill stop if an error is detected during pow er up. 8NO Errors The sy stem boot w ill not stop for any error that may be detected and y ou w ill be prompted. 8All Errors Whenev er the BIOS detects a non-fatal error the sy stem w ill be stopped. 8All, But Key board The sy stem boot w ill not stop for a key board error; it w ill stop for all other errors. (Default v alue) 8All, But Diskette The sy stem boot w ill not stop for a disk error; it w ill stop for all other errors. 8All, But Disk/Key The sy stem boot w ill not stop for a key board or disk error; it w ill stop for all other errors. • Memory The category is display -only w hich is determined by POST (Pow er On Self Test) ofthe BIOS. Bas e Memory The POST of the BIOS w ill determine the amount of base (or conv entional) memory installed in the sy stem. The v alue of the base memory is ty pically 512 K for sy stems w ith 512 K memory installed on the motherboard, or 640 K for sy stems w ith 640 K or more memory installed on the motherboard. Extended Memory The BIOS determines how much ex tended memory is present during the POST. This is the amount of memory located abov e 1 M B in the C PU ’s memory address map. GA-8SR533 Series Motherboard -28 Advanced BIOS Features CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Adv anced BIOS Features First Boot Dev ice Second Boot Dev ice Third Boot Dev ice Boot Up Floppy Seek Init Display First Floppy HDD-0 CDROM Disabled AGP Item Help Menu Lev el • Select Boot Dev ice priority [Floppy ] Boot from floppy [LS120] Boot from LS120 [HDD-0] Boot from First HDD [HDD-1] Boot from second HDD higf: Mov e Enter:Select F5:Prev ious Values +/-/PU/PD:Value F10:Sav e F6:Fail-Safe Defaults ESC:Ex it F1:General Help F7:Optimized Defaults Figure 3: Adv anced BIOS Features • Firs t / S econd / Third Boot Device 8Floppy Select y our boot dev ice priority by Floppy . 8LS120 Select y our boot dev ice priority by LS120. 8HDD-0~3 Select y our boot dev ice priority by HDD-0~3. 8SCSI Select y our boot dev ice priority by SCSI. 8CDROM Select y our boot dev ice priority by CDROM. 8ZIP Select y our boot dev ice priority by ZIP. 8USB-FDD Select y our boot dev ice priority by USB-FDD. 8USB-ZIP Select y our boot dev ice priority by USB-ZIP. 8USB-CDROM Select y our boot dev ice priority by USB-CDROM. 8USB-HDD Select y our boot dev ice priority by USB-HDD. 8LAN Select y our boot dev ice priority by LAN. 8Disabled Select y our boot dev ice priority by Disabled. -29 -BIOS Setup English EnglishEnglish • Boot Up Fl oppy S eek During POST, BIOS w ill determine the floppy disk driv e installed is 40 or 80 tracks. 360 K ty pe is 40 tracks 720 K, 1.2 M and 1.44 M are all 80 tracks. 8Enabled BIOS searches for floppy disk driv e to determine it is 40 or 80 tracks. Note that BIOS can not tell from 720 K, 1.2 M or 1.44 M driv e ty pe as they are all 80tracks. 8Disabled BIOS w ill not search for the ty pe of floppy disk driv e by track number. Note that there w ill not be any w arning message if the driv e installed is 360 K. (Default v alue) CInit Dis play Firs t 8AGP Set Init Display First to AGP. (Default v alue) 8PCI Set Init Display First to PCI. GA-8SR533 Series Motherboard -30 Integrated Peripherals CMOS Setup Utility -Copy right (C) 1984-2002 Aw ard Softw are Integrated Peripherals IDE1 Conductor Cable IDE2 Conductor Cable On-Chip Primary PCI IDE On-Chip Secondary PCI IDE AC97 Audio USB Controller USB Legacy Support Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select x UR2 Duplex Mode Onboard Parallel Port Parallel Port Mode x ECP Mode Use DMA Game Port Address Midi Port Address Midi Port IRQ Auto Auto Enabled Enabled Enabled Enabled Disabled 3F8/IRQ4 2F8/IRQ3 Normal Half 378/IRQ7 SPP 3 201 330 10 Item Help Menu Lev el • [Auto] Auto-detect IDE cable ty pe [ATA66/100] Set Conductor cable to ATA66/100(80-pins) [ATA33] Set Conductor cable to ATA33(40-pins) higf: Mov e Enter:Select F5:Prev ious Values +/-/PU/PD:Value F10:Sav e F6:Fail-Safe Defaults ESC:Ex it F1:General Help F7:Optimized Defaults Figure 4: Integrated Peripherals -31 -BIOS Setup English EnglishEnglish • IDE1 Condu ctor Cable 8Auto Will be automatically detected by BIOS. (Default Value) 8ATA66/100 Set IDE1 Conductor Cable to ATA66/100 (Please make sure y our IDE dev ice and cable is compatible w ith ATA66/100). 8ATA33 Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE dev ice and cable is compatible w ith ATA33). • IDE2 Condu ctor Cable 8Auto Will be automatically detected by BIOS. (Default Value) 8ATA66/100 Set IDE2 Conductor Cable to ATA66/100 (Please make sure y our IDE dev ice and cable is compatible w ith ATA66/100). 8ATA33 Set IDE2 Conduct...