Votes - 1, Average rating: 5
(
)
)
|
manual abstract
Figure 3. Make sure the CPU fan is plugged to the CPU fan connector, than install complete. Socket Actuation Lever 8S661FXM-RZ Motherboard - 10 - 11 - Hardware Installation Process English Step 2: Install memory modules DDR Support Unbuffered DDR DIMM Sizes type: 64 Mbit (2Mx8x4 banks) 64 Mbit (1Mx16x4 banks) 128 Mbit(4Mx8x4 banks) 128 Mbit(2Mx16x4 banks) 256 Mbit(8Mx8x4 banks) 256 Mbit(4Mx16x4 banks) 512 Mbit(16Mx8x4 banks) 512 Mbit(8Mx16x4 banks) Notch Before installing the memory modules, adhere to the following warning: Please note that the DIMM module can only fit in one direction due to the one notch. Wrong orientation will cause improper installation. Please change the insert orientation. The motherboard has 2 dual inline memory module (DIMM) sockets. The BIOS will automatically detects memory type and size. To install the memory module, just push it vertically into the DIMM socket. The DIMM module can only fit in one direction due to the notch. Memory size can vary between sockets. 1. The DIMM socket has a notch, so the DIMM memory module can only fit in one direction. 2. Insert the DIMM memory module vertically into the DIMM socket. Then push it down. 3. Close the plastic clip at both edges of the DIMM sockets to lock the DIMM module. Reverse the installation steps when you wish to remove the DIMM module. English English Step 3: Install expansion cards 1. Read the related expansion card's instruction document before install the expansion card into the computer. 2. Please make sure your AGP card is AGP 4X/8X (1.5V). 3. Please carefully pull out the small white- drawable bar at the end of the AGP slot when you try to install/ Uninstall the AGP card. Please align the AGP card to the onboard AGP slot and press firmly down on the slot .Make sure your AGP card is locked by the small white- drawable bar. AGP Card Step 4: Install I/O Peripherals Cables Step 4-1: I/O Back Panel Introduction ................ • PS/2 Keyboard and PS/2 Mouse connector This connector supports standard PS/2 keyboard and PS/2 mouse. • Parallel port (LPT) Device like printer can be connected to Parallel port. • Serial port (COMA) Mouse and modem etc. can be connected to Serial port. • VGA port Monitor can be connected to VGA port. • Game/MIDI port This connector supports joystick, MIDI keyboard and other relate audio devices. • Line Out jack Connect the stereo speakers or earphone to this connector. • Line In jack Devices like CD-ROM, walkman etc. can be connect to Line In jack. 8S661FXM-RZ Motherboard - 12 - 13 - Hardware Installation Process English ..MIC In jack Microphone can be connect to MIC In jack. After installation of the audio driver, you are able to use 2/4/6-channel audio feature by software selection. You can connect "Front speaker" to "Line Out" jack, Connect "Rear speaker" to "Line In" jack and connect "Center/Subwoofer" to "MIC In" jack. .. LAN port LAN is fast Ethernet with 10/100Mbps speed. .. USB port Before you connect your device(s) into USB connector(s), please make sure your device(s) such as USB keyboard, mouse, scanner, zip, speaker...etc. Have a standard USB interface. Also make sure your OS supports USB controller. If your OS does not support USB controller, please contact OS vendor for possible patch or driver upgrade. For more information please contact your OS or device(s) vendors. Step 4-2: Connectors Introduction 1 1) ATX_12V 2) ATX 3) CPU_FAN 4) SYS_FAN 5) FDD 6) IDE1 / IDE2 7) F_PANEL 8) PWR_LED 9) BAT 10) F_AUDIO 11) CD_IN 12) SPDIF_IO 13) SUR_CEN 14) F_USB1 / F_USB2 15) CLR_CMOS 16) COMB 17) CI* ("*" Only for 8S661FXM-RZ Rev. 1.1) 2 5 8 3 6 12 4 15 7 10 11 13 14 9 16 17* 8S661FXM-RZ Motherboard - 14 - English 1) ATX_12V (+12V Power Connector) This connector (ATX _12V) supplies the CPU operation voltage (Vcore). If this " ATX_ 12V connector" is not connected, system cannot boot. Pin No. Definition 1 GND 2 GND 3 +12V 4 +12V 2) ATX (ATX Power) AC power cord should only be connected to your power supply unit after ATX power cable and other related devices are firmly connected to the mainboard. 1 20 10 11 Pin No. Definition 1 3.3V 2 3.3V 3 GND 4 VCC 5 GND 6 VCC 7 GND 8 Power Good 9 5V SB (stand by +5V) 10 +12V Pin No. Definition 11 3.3V 12 -12V 13 GND 14 PS_ON(soft on/off) 15 GND 16 GND 17 GND 18 -5V 19 VCC 20 VCC 3) CPU_FAN (CPU FAN Connector) Please note, a proper installation of the CPU cooler is essential to prevent the CPU from running under abnormal condition or damaged by overheating.The CPU fan connector supports Max. current up to 600 mA. Pin No. Definition 1 GND 2 +12V 3 Sense 1 4 3 2 1 - 15 - Hardware Installation Process English 4) SYS_FAN (System FAN Connector) This connector allows you to link with the cooling fan on the system case to lower the system temperature. Pin No. Definition 1 GND 2 +12V 3 Sense 1 5) FDD (Floppy Connector) Please connect the floppy drive ribbon cables to FDD. It supports 360K,720K,1.2M,1.44M and 2.88Mbytes floppy disk types. The red stripe of the ribbon cable m...