Votes - 0, Average rating: 0
(
)
)
|
manual abstract
(Default value) !All, But Diskette The system boot will not stop for a disk error; it will stop for all other errors. !All, But Disk/Key The system boot will not stop for a keyboard or disk error; it will stop for all other errors. • !!!!!Memory The category is display-only which is determined by POST (Power On Self Test) of the BIOS. Base Memory The POST of the BIOS will determine the amount of base (or conventional) memory installed in the system. The value of the base memory is typically 512 K for systems with 512 K memory installed on the motherboard, or 640 K for systems with 640 K or more memory installed on the motherboard. Extended Memory The BIOS determines how much extended memory is present during the POST. This is the amount of memory located above 1 MB in the CPU.s memory address map. English -27 -BIOS Setup EnglishEnglish Advanced BIOS Features CMOS Setup Utility-Copyright (C) 1984-2002 Award Software Advanced BIOS Features First Boot Device Second Boot Device Third Boot Device Boot Up Floppy Seek Init Display First Graphics Aperture Size Graphics Share Memory Floppy HDD-0 CDROM Disabled Onboard/AGP 128MB 8MB Item Help Menu Level • • "#$%: Move Enter:Select F5:Previous Values +/-/PU/PD:Value F10:Save ESC:Exit F1:General HelpF6:Fail-Safe Defaults F7:Optimized Defaults Figure 3: Advanced BIOS Features • !!!!!First / Second / Third Boot Device !Floppy Select your boot device priority by Floppy. !LS120 Select your boot device priority by LS120. !HDD-0~3 Select your boot device priority by HDD-0~3. !SCSI Select your boot device priority by SCSI. !CDROM Select your boot device priority by CDROM. !ZIP Select your boot device priority by ZIP. !USB-FDD Select your boot device priority by USB-FDD. !USB-ZIP Select your boot device priority by USB-ZIP. !USB-CDROM Select your boot device priority by USB-CDROM. !USB-HDD Select your boot device priority by USB-HDD. !LAN Select your boot device priority by LAN. !Disabled Select your boot device priority by Disabled. GA-8ILMT4 Motherboard - 28 • !!!!!Boot Up Floppy Seek During POST, BIOS will determine the floppy disk drive installed is 40 or 80 tracks. 360 K type is 40 tracks 720 K, 1.2 M and 1.44 M are all 80 tracks. !Enabled BIOS searches for floppy disk drive to determine it is 40 or 80 tracks. Note that BIOS can not tell from 720 K, 1.2 M or 1.44 M drive type as they are all 80tracks. !Disabled BIOS will not search for the type of floppy disk drive by track number. Note that there will not be any warning message if the drive installed is 360 K. (Default value) • !!!!!Init Display First !Onboard/AGP Set Init Display First to onboard/AGP. (Default value) !PCI Set Init Display First to PCI. • !!!!!Graphics Aperture Size !128MB Set Graphics Aperture Size to 128MB. (Default value) !Disabled Disable this function. • !!!!!Graphics Share Memory !8MB Set Graphics Share Memory to 8MB. (Default value) !1MB Set Graphics Share Memory to 1MB. English -29 -BIOS Setup EnglishEnglish Integrated Peripherals CMOS Setup Utility-Copyright (C) 1984-2002 Award Software Integrated Peripherals On-Chip Primary PCI IDE On-Chip Secondary PCI IDE IDE1 Conductor Cable IDE2 Conductor Cable USB Controller USB Keyboard Support USB Mouse Support AC97 Audio Onboard LAN Onboard LAN Boot ROM Onboard Serial Port 1 Onboard Serial Port 2 UART Mode Select x UR2 Duplex Mode Onboard Parallel Port Parallel Port Mode Game Port Address Midi Port Address Midi Port IRQ Enabled Enabled Auto Auto Enabled Disabled Disabled Auto Enabled Disabled 3F8/IRQ4 2F8/IRQ3 Normal Half 378/IRQ7 SPP 201 330 10 Item Help Menu Level • If a hard disk controller card is used, set at Disable [Enabled] Enable onboard IDE PORT [Disabled] Disable onboard IDE PORT • "#$%: Move Enter:Select F5:Previous Values +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help F6:Fail-Safe Defaults F7:Optimized Defaults Figure 4: Integrated Peripherals • !!!!!On-Chip Primary PCI IDE !Enabled Enable onboard 1st channel IDE port. (Default value) !Disabled Disable onboard 1st channel IDE port. GA-8ILMT4 Motherboard - 30 • !!!!!On-Chip Secondary PCI IDE !Enabled Enable onboard 2nd channel IDE port. (Default value) !Disabled Disable onboard 2nd channel IDE port. • !!!!!IDE1 Conductor Cable !Auto Will be automatically detected by BIOS. (Default Value) !ATA66/100 Set IDE1 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). !ATA33 Set IDE1 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). • !!!!!IDE2 Conductor Cable !Auto Will be automatically detected by BIOS. (Default Value) !ATA66/100 Set IDE2 Conductor Cable to ATA66/100 (Please make sure your IDE device and cable is compatible with ATA66/100). !ATA33 Set IDE2 Conductor Cable to ATA33 (Please make sure your IDE device and cable is compatible with ATA33). • !!!!!USB Controller !Enabled Enable USB Controller. (Default value) !Disabled Disable USB Controller. • !!!!!USB Keyboard Support !Enabled Enable USB ...