Votes - 0, Average rating: 0
(
)
)
|
manual abstract
3 1 4 2 Pin No. Definition 1 GND 2 GND 3 +12V 4 +12V Pin No. Definition 1 3.3V 2 3.3V 3 GND 4 VCC 5 GND 6 VCC 7 GND 8 Power Good 9 5V SB(stand by +5V) 10 +12V 11 +12V 12 3.3V(Only for 24pins ATX) 13 3.3V 14 -12V 15 GND 16 PS_ON(soft On/Off) 17 GND 18 GND 19 GND 20 -5V 21 VCC 22 VCC 23 VCC 24 GND 1 12 13 24 GA-8I915G-MF/GA-8I915GM Motherboard - 20 - English 1 5) FDD (Floppy Connector) The FDD connector is used to connect the FDD cable while the other end of the cable connects to the FDD drive. The types of FDD drives supported are: 360KB, 720KB, 1.2MB, 1.44MB and 2.88MB. Please connect the red power connector wire to the pin1 position. CPU_FAN SYS_FAN 1 2 1 34 33 3/4) CPU_FAN / SYS_FAN (Cooler Fan Power Connector) The cooler fan power connector supplies a +12V power voltage via a 3-pin/4-pin (only for CPU_FAN) power connector and possesses a foolproof connection design. Most coolers are designed with color-coded power connector wires. A red power connector wire indicates a positive connection and requires a +12V power voltage. The black connector wire is the ground wire (GND). Please remember to connect the power to the cooler to prevent system overheating and failure. Caution! Please remember to connect the power to the CPU fan to prevent CPU overheating and failure. Pin No. Definition 1 GND 2 +12V 3 Sense 4 Speed Control (Only for CPU_FAN) - 21 - Hardware Installation English 6) IDE (IDE Connector) An IDE device connects to the computer via an IDE connector. One IDE connector can connect to one IDE cable, and the single IDE cable can then connect to two IDE devices (hard drive or optical drive). If you wish to connect two IDE devices, please set the jumper on one IDE device as Master and the other as Slave (for information on settings, please refer to the instructions located on the IDE device). 1 7 Pin No. Definition 1 GND 2 TXP 3 TXN 4 GND 5 RXN 6 RXP 7 GND 2 1 40 39 7) S_ATA0/S_ATA1/S_ATA2/S_ATA3 (Serial ATA Connector, Controlled by ICH6) Serial ATA can provide 150MB/s transfer rate. Please refer to the BIOS setting for the Serial ATA and install the proper driver in order to work properly. GA-8I915G-MF/GA-8I915GM Motherboard - 22 - English 8) F_PANEL (Front Panel Jumper) Please connect the power LED, PC peaker, reset switch and power switch etc of your chassis front panel to the F_PANEL connector according to the pin assignment below. HD (IDE Hard Disk Active LED) Pin 1: LED anode(+) Pin 2: LED cathode(-) SPEAK (Speaker Connector) Pin 1: VCC(+) Pin 2- Pin 3: NC Pin 4: Data(-) RES (Reset Switch) Open: Normal Operation Close: Reset Hardware System PW (Power Switch) Open: Normal Operation Close: Power On/Off MSG(Message LED/Power/Sleep LED) Pin 1: LED anode(+) Pin 2: LED cathode(-) NC NC 1 2 19 20 HDHD+ RES+ RESNC SPEAKMSGMSG+ PWPW+ SPEAK+ Speaker Connector IDE Hard Disk Active LED Message LED/ Power/ Sleep LED Power Switch Reset Switch - 23 - Hardware Installation English 1 Pin No. Definition 1 MPD+ 2 MPD- 3 MPD- 1 9 2 10 9) PWR_LED PWR_LED is connect with the system power indicator to indicate whether the system is on/off. It will blink when the system enters suspend mode. Pin No. Definition 1 MIC2_L 2 GND 3 MIC2_R 4 -ACZ_DET 5 Line2_R 6 FSENSE1 7 FAUOIO_JD 8 No Pin 9 LINE2_L 10 FSENSE2 Pin No. Definition 1 MIC 2 GND 3 MIC Power 4 N/A 5 Line Out (R) 6 N/A 7 N/A 8 No Pin 9 N/A 10 Line Out (L) HD Audio: AC'97 Audio: HD Audio is the default setting for this connector. To enable AC'97 Audio, from BIOS settings, set Front Panel Type under Integrated Peripherals to AC97. 10) AZALIA_FP (Front Audio Connector) This connector is supported to connect HD(High Definition) Audio and AC’97 Audio. Check the pin assignment carefully while you connect the audio panel cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional audio panel cable, please contact your local dealer. GA-8I915G-MF/GA-8I915GM Motherboard - 24 - English 11) CD_IN (CD IN) Connect CD-ROM or DVD-ROM audio out to the connector. 1 Pin No. Definition 1 CD-L 2 GND 3 GND 4 CD -R 1 2 9 10 12) F_ USB1 / F_USB2 (Front USB Connector) Be careful with the polarity of the front USB connector. Check the pin assignment carefully while you connect the front USB cable, incorrect connection between the cable and connector will make the device unable to work or even damage it. For optional front USB cable, please contact your local dealer.The "USB Device Wake up From S3" is only supported by rear USB ports. Pin No. Definition 1 Power 2 Power 3 USB DX- 4 USB Dy- 5 USB DX+ 6 USB Dy+ 7 GND 8 GND 9 No Pin 10 NC - 25 - Hardware Installation English 2 10 1 9 F2_1394 F1_1394 Pin No. Definition 1 TPA2+ 2 TPA2- 3 GND 4 GND 5 TPB2+ 6 TPB2- 7 No Pin 8 Power 9 Power 10 GND Pin No. Definition 1 Power 2 Power 3 TPA0+ 4 TPA0- 5 GND 6 GND 7 TPB0+ 8 TPB0- 9 Power 10 Power 11 TPA1+ 12 TPA1- 13 GND 14 No Pin 15 TPB1+ 16 TPB1- 14) IR Be careful with the polarity of the IR connector while you connect the IR. Please cont...