Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
On/off switch 2. Lock-off button 3. Blade release button 4. Grass Shear blade (GSL35, GSL75, GSN30, GSN35) 5. Shrub Trim blade (GSL35, GSL75, GSN32, GSN35) 6. Blade cover (not shown) Assembly WARNING: Avoid accidentally switching the tool on 52143during assembly. Fitting and removing the blade (fig. A, B, C) The shear blade (4) has been designed for trimming grass and weeds. The trim blade (5) has been designed for trimming hedges and shrubs. • To remove the blade cover (6). Push and hold the blade release button (3) in the direction of the arrow (fig. A) • Slide the blade cover (6) backwards and lift it off (fig. A-1). Make sure that the blade is located under edge marked .X. (fig. B-1) and then lower the blade onto the pins. A B • While holding the blade pins (Fig. C), locate the (6) and slide it forward (fig. Note: No alignment of blade with drive pin is required and operation the blade cover release button required when re-fitting the blade cover. Charging Procedure The battery needs to be charged before first use and whenever it fails to produce power on jobs that were easily done before. When charging the battery for the first time, or after prolonged storage, it will only accept an 80% charge. After several charge and discharge cycles, the battery capacity. The battery may become warm while charging; this normal and does not indicate a problem. C WARNING: Do not charge the battery at ambient temperatures below 36° F (2°C) or above 104°F (40°C). Recommended charging temperature: Approximately 75°F (24°• Note: The charger plug incorporates lock outs to prevent the use of incorrect chargers. The plug must be correctly oriented when inserted. • Insert the charger plug into the charger connector at the rear of the tool (fig. D) . • Plug the charger into a 120V outlet. • Charge the tool for 16 hours before first use. For catalog numbers GSL35, GSL75: • The charger indicator light will come on indicating that the tool is charging. D • When the charge is complete the light will go out. For catalog numbers GSN30,GSN32, GSN35: • The charger indicator light will come on indicating that the tool is charging. • The light will stay on as long as the charger is connected to the tool and plugged into a working outlet. 4 5 • It WILL NOT flash, or go out when the charging cycle is complete. To maximize the lifetime of the battery, it is recommended to keep the battery connected to the charger whenever the tool is not in use. When the battery is full, the power consumption of the charger is negligible. Use CAUTION: Let the tool work at its own pace. Do not overload. Switching on and off Switching on • Push and hold the lock button (2) (fig. E) to the right or to the left and then squeeze the on/off switch (1). • Release the lock-off button. Switching off • Release the on/off switch (1). WARNING: Never attempt to lock the switch in the on position. Hints for optimum use (figs. F, G, H & I) Trimming grass • In order to achieve optimum cutting results, only cut dry grass. • Hold the tool as shown in fig. F & G. Keep your other hand well away from the blade. Maintain a stable working position so that you do not slip. Do not overreach. • When cutting long grass, work in stages from the top. Take small cuts. • Keep the tool away from hard objects and delicate plants. • If the tool starts running slowly, reduce the load. • To make a closer cut, slightly tilt the tool. Trimming hedges • Slightly tilt the tool (up to 15° relative to the line of cut) so that the blade tips point slightly towards the hedge (fig. H). This will cause the blades to cut more effectively. • Start by trimming the top of the hedge. Hold the tool at the desired angle and move it steadily along the line of cut. The double-sided blade allows you to cut in either direction. • In order to obtain a very straight cut, stretch a piece of string along the length of the hedge at the desired height. Use the string as a guide line, cutting just above it. • In order to obtain flat sides, cut upwards with the growth (fig. I). Younger stems move outwards when the blade cu...
Other models in this manual:Hair Clippers - GSL75 (1.23 mb)
Hair Clippers - GSN30 (1.23 mb)
Hair Clippers - GSN32 (1.23 mb)
Hair Clippers - GSN35 (1.23 mb)