Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Cutting ear hair Clean outer area of ear and make sure it is free of wax. 1 Switch the groomer on. 2 Move the tip softly around the edge of ear to remove hairs extending beyond the outer ear.Then carefully insert the tip into outer ear (fig. 13) Do not insert the tip more than 0.5 centimetres into your ear as this could damage the eardrum. Cutting eyebrows It is not recommended that you use the groomer to define or trim the entire eyebrow. 1 Switch the groomer on. 2 Use the tip to cut individual eyebrow hairs (fig. 14). 3 Put on the groomer at the root of the nose and move it along the eyebrow into the direction of hairgrowth (fig. 15). Do not trim your eyelash, be careful not to get too close to your eyelashes and eyes. Cleaning Do not use abrasives, scourers or liquids such as alcohol, petrol or acetone to clean the appliance. Do not immerse the appliance into water. 1 Make sure the appliance is switched off and disconnected from the mains before you start cleaning it. 2 Remove the comb attachment. 3 Open the cutting unit by pushing it backwards (fig. 16). Be careful that the cutting element does not drop down. 4 Clean the cutting unit and the inside of the appliance with the brush supplied (2) 5 Reassemble the cutting unit by inserting the hook onto the appliance and pushing it back onto the appliance until you hear a click (fig. 17). Cleaning grooming attachment 1 Remove the grooming attachment by pushing it backwards (fig. 18). 2 Blow and/or shake hairs out of the grooming attachment. 3 Reassemble one of the two attachments on the appliance (fig. 19). Replacing the cutting unit A worn or damaged cutting unit should only be replaced with an original Philishave cutting unit, available from authorised Philips service centres. 1 Remove the old cutting unit. 2 Put the new cutting unit back onto the appliance until you hear a click. Storage 1 Store the appliance and attachments in the stand to prevent damaging (fig. 20). Environment The built-in rechargeable battery contains substances that may harm the environment. Remove the rechargeable battery when you discard the appliance. Do not throw the battery away with the normal household waste but hand it in at an official collection point. You can also take the appliance to a Philips service centre, where the staff will be happy to help you remove the battery and dispose of it in an environmentally safe way. 1 Disconnect the appliance from the mains and let the appliance run until the motor stops. 2 Slide in the Guide Comb Attachment. Pull cutting unit back to remove it (fig. 21). 3 Put a screw driver between the housing part and the metal eccentric part and push it down until the housing part will be opened (fig. 22). 4 Pull the rechargeable battery (1) and the on/off circuit board (2) out of the housing (fig. 23). 5 Insert the screwdriver into the small slot in the printed circuit board marked with an arrow. Push the screwdriver down until part of the printed circuit board breaks off (fig. 24). 6 Remove the battery form the plastic part using a screwdriver. Do not attempt to replace battery. 7 Discard the appliance. Do not connect the appliance to the mains again after the battery has been removed. Service und Information If you need information or if you have a problem, please visit the Philips Web site at or contact the Philips Customer Care Centre in your country (you will find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV. Allgemeine Beschreibung A 2D Konturen-Kamm B 3-dimensionale abgerundete Schneiden aus Chrom-Stahl C Schnittlangenregler D Ein-/Ausschalter E Buchse fur das Geratekabel F Reinigungsburste G Frisierkamm H Ladekontroll-Lampe I Steckernetzgerat J Geratestecker K Aufsatz zum Trimmen von Haaren an Nase, Ohren, Augenbrauen L Geratestander M Schneideaufsatz Wichtig . Prufen Sie, bevor Sie das Gerat in Betrieb nehmen, ob die Spannungsangabe auf dem Gerat mit der ortlichen Netzspannung ubereinstimmt. . Achten Sie darauf, da. das Gerat nicht na. wird. . Dieses Gerat ist ausschlie.lich zum Schneiden menschlicher Barte und zum Trimmen von Haaren an Nase, Ohren,Augenbrauen, Schnurrbarten und Koteletten bestimmt. . Bewahren Sie das Gerat au.er Reichweite von Kindern auf. Den Akku aufladen Laden Sie den Akku voll auf, bevor Sie das Gerat zum ersten Mal benutzen. 1 Achten Sie darauf, dass das Gerat ausgeschaltet ist. 2 Stecken Sie das Steckernetzgerat in das Gerat (Abb. 2). 3 Stecken Sie den Netzstecker in die Steckdose. . Nach kurzer Zeit beginnt die grune Kontroll- Lampe zu leuchten und zeigt an, dass der Akku geladen wird (Abb. 3). Nach ca. 10 Stunden ist der Akku voll aufgeladen. Halten Sie das Gerat zum Aufladen nicht langer als 24 Steunden am Netz, das erhoht die Nutzungsdauer des Akkus. Mit dem voll aufgeladenen Akku konnen Sie das Gerat bis zu 40 Minut...