Votes - , Average rating:
(
)
)
Manafacture: Philips
File size: 453.67 kb
File name:
Language of manual:
The document is loading, please wait
 |
The document is loading, please wait
manual abstract
Check if the voltage indicated on the mains plug corresponds to the mains voltage in your home before you connect the appliance. . Make sure the appliance does not get wet. . Charge and store the appliance at a temperature between 15c and 35cC. Charging Charge the appliance fully before you star t using it for the first time. Make sure the appliance is switched off while charging. Insert the appliance plug into the appliance. Insert the mains plug into the wall socket. 1 2 B The pilot light will go on to indicate that the appliance is charging. It will take approx. 12 hours to fully charge the batter y. Do not charge the appliance for more than 24 hours. A fully charged appliance has a cordless clipping time of up to 40 minutes. ENGLISH Corded clipping C C . To clip with the hair clipper connected to the mains: Switch the hair clipper off, connect it to the mains and wait a few seconds before switching it on. If the batter y is completely empty: wait a few minutes before switching the appliance on. Do not run the appliance from the mains when the batter y is fully charged. Preparing for clipping . See also the booklet 'Modelling and styling'. Clipping with comb attachment: 1 2 3 4 5 Select the small or large comb attachment, depending on the desired hair length (see table). Slide the arms carefully into the guiding grooves of the appliance until you hear a click. Keep the adjustment button pressed in and slide the comb attachment to the desired position (see table). Release the adjustment button to lock the comb. Switch the appliance on. C 6 ENGLISH If a lot of hair has accumulated in the comb, remove the comb attachment and blow and/or shake the hair out of the comb. Cutting length settings Small comb Large comb setting hair length setting hair length 1 4 mm 8 24 mm 2 7 mm 9 27 mm 3 10 mm 10 30 mm 4 13 mm 11 33 mm 5 16 mm 12 35 mm 6 19 mm 13 38 mm 7 21 mm 14 40 mm Clipping without comb attachment 1 Pull the comb attachment off the appliance to remove it. Clean and recharge the appliance ever y time you have used it. Cleaning Do not use abrasives, scourers or liquids such as alcohol, petrol or acetone to clean the appliance. 1 Make sure the appliance is switched off and disconnected from the mains before you start cleaning it. ENGLISH C C C 2 3 4 5 6 Remove the comb attachment. Remove the cutting unit. Clean the cutting unit and the inside of the appliance with the brush supplied. To reassemble the clipper, insert the hook of the cutting unit into the housing. Push the cutting unit until you hear a click. Replacement A worn or damaged cutting unit should only be replaced with an original Philips cutting unit. Environment The built-in rechargeable batter y contains substances which may pollute the environment. Remove the rechargeable batter y when you discard the appliance. ENGLISH C C C C Do not throw the batter y away with the normal household waste but dispose of it at an official collection point. You can also take the appliance to a Philips ser vice centre, where staff will be happy to help you remove the batter y and dispose of it in an environmentally safe way. Disconnect the appliance from the mains and let the appliance run until the motor stops. Remove the cutting unit. Remove the metal clip by means of a screwdriver. 4 Open the housing. 5 Pull the battery holder out of the appliance. 1 2 3 ENGLISH 6 Insert a screwdriver into the small slot in the printed circuit board. Push the screwdriver down until part of the printed circuit board breaks off. C C 7 Separate the battery from the plastic part by means of a screwdriver. 8 Dispose of the battery and the other components in an environmentally safe way. Do not connect the appliance to the mains again after it has been opened! For telephone numbers of the Philips Helpdesk, see the Worldwide Guarantee leaflet. Wazne POLSKI10 C . Przed podlaczeniem urzadzenia upewnij sie, czy napiecie podane na wtyczce jest zgodne z napieciem sieci elektrycznej. . Chron urzadzenie przed wilgocia. . Laduj i przechowuj urzadzenie w temperaturze od 15°C do 35°C. Ladowanie Przed uzyciem po raz pierwszy wykonaj pelne ladowanie urzadzenia. Przed rozpoczeciem ladowania upewnij sie, ze urzadzenie jest wylaczone. 1 2 Wloz wtyczke aparatowa do gniazda w urzadzeniu. Wloz wtyczke sieciowa do gniazda sieciowego. B Zapali sie lampka kontrolna informujaca, ze urzadzenie jest ladowane. Pelne naladowanie akumulatora trwa ok. 12 godzin. Nie laduj akumulatora dluzej niz 24 godziny. Czas strzyzenia tr ymerem z calkowicie naladowanym akumulatorem wynosi do 40 minut. POLSKI 11 C C Strzyzenie z trymerem podlaczonym do sieci . Aby strzyc trymerem podlaczonym do sieci: Wylacz tr ymer, podlacz go do sieci i wlacz go po odczekaniu kilku sekund. Jezeli akumulator zostal c...