Votes - 0, Average rating: 0
(
)
)
|
manual abstract
Comb the hair in the growth direction (Fig. 3). Clipping with comb The appliance comes with three combs for 15 different hair lengths. The minimum remaining hair length is 1.6mm and the maximum remaining hair length is 41mm. 1 Select the comb you want to use. The table shows how long the hair will be after clipping at the different settings of the small comb and large comb. settings of the small and large comb and large 1 3mm 23mm 6mm 3 9mm 29mm 12mm 5 15mm 35mm 18mm 2 4 6 26mm 32mm 38mm Setting Hair length after clippingwith small comb Hair length after clippingwith largecomb 7 21mm 41mm Tip:Write down the settings you have used to create a certain hairstyle as a reminder for future clipping sessions. stubble comb for a ‘stubble look’ - To create a ‘stubble look’, clip with the small comb set to setting 1 (3mm) first. - Then clip the hair with the stubble comb for a hair length of 1.6mm. 2 Slide the selected comb into the guiding grooves on both sides of the handle (‘click’) (Fig. 4). 3 , To set the comb to the desired setting, press the setting selector (1) and slide the comb tothe desired hair length setting (2) (Fig. 5). The setting indications on the comb show the selected setting. 4 Put the adapter into the wall socket. 5 Switch on the appliance. 6 Move the appliance through the hair slowly. -To clip in the most effective way, move the appliance against the direction of hair growth. -Since all hair does not grow in the same direction, you need to move the appliance in different directions (upward, downward or across) (Fig. 6). -Make sure that the flat par t of the comb is always fully in contact with the scalp to obtain an even result. -Make overlapping passes over the head to ensure that you cut all the hair that needs to be cut. -To achieve a good result with curly, sparse or long hair, use a hand comb to guide the hair towards the appliance. 7 Regularly remove cut hair from the comb. If a lot of hair has accumulated in the comb, remove the comb from the appliance and blow and/or shake the hair out of it. Contouring without comb You can use the appliance without comb to clip hair ver y close to the skin (0.6mm) or to contour the neckline and the area around the ears. Be careful when you clip without comb because the cutting element removes every hair it touches. 1 2 3 Pull the comb off the appliance (Fig. 7). Before you start to contour the hairline around the ears, comb the hair ends over the ears. Tilt the appliance in such a way that only one edge of the cutting element touches the hair ends when you shape the contours around the ears (Fig. 8). Only cut the hair ends. The hairline should be close to the ear. 4 To contour the neckline and sideburns, turn the appliance and make downward strokes (Fig. 9). Move the appliance slowly and smoothly. Follow the natural hairline. Cleaning Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone or ethereal oils to clean the appliance. Note:The appliance does not need any lubrication. Clean the appliance ever y time you have used it. 1 2 3 Make sure the appliance is switched off and disconnected from the mains. Remove the comb from the appliance. To remove the clipping attachment, turn it anticlockwise until the open dot on thehandle is aligned with the arrow on the attachment (1).Then lift the attachment off the handle (2) (Fig. 10). 4 Push the centre top end of the cutting element upwards with your thumb until it opens and then pull it off the appliance (Fig. 11). Be careful that the cutting element does not fall on the floor. 5 6 7 Clean the cutting element with warm water (max. 40°C). Clean the clipping attachment under warm running water to flush out the cut hair that has accumulated in the attachment (Fig. 12). After cleaning, place the lug of the cutting element in the slot of the clipping attachmentand push the cutting element back onto the clipping attachment (Fig. 13). 8 Clean the handle and the adapter with the cleaning brush supplied or a dry cloth. Note:The handle and the adapter are not waterproof. 9 Let the cutting element and the clippingattachment dry completely before you reassemble the appliance. Note: Make sure the electrical contacts of the clipping attachment are dry before you reattach the attachment to the handle. 10 To attach the clipping attachment, put it on the handle in such a way that the open dot on the handle is aligned with the arrow on the clipping attachment (1).Then turn the clipping attachment clockwise until the arrow is aligned with the solid dot on the handle (2) (Fig. 14). Replacement If the adapter is damaged, always have it replaced with one of the original type in order to avoid a hazard. Only replace a damaged or worn attachment or comb with an original Philips replacement attachment or comb. Philips replacement par ts (clipping attachment, cutting element, combs, handle and adapter) are available from your Philips dealer and authorised Philips ser vice cen...