Votes - 1, Average rating: 3 ( )

Manafacture: Electrolux File size: 354.89 kb File name: Language of manual:

The wire which is coloured BROWN must be connected to the Terminal which is marked with the letter 'L' or coloured RED. 4. It is important that the outer sheath is clamped correctly into the 3-pin plug. 5. If in doubt consult your local Service Repairer or qualified electrician before the machine is used. 6. A 13 Amp fuse must be fitted to the Mains Plug. 7. The normal plug fuse and household fuse only protect the electrical equipment and are not a safeguard against electrocution. E L F U S EN BLACK OR BLUE RED OR BROWN If your product is hard wired i.e. non- detachable mains electric cable, a conversion kit and extension cable is available from all Electrolux Outdoor Products Approved Service Centres which can be found in your local Yellow Pages. Assembly Assembly of Handguard. 1. Insert Handguard into slot as illustrated in figure A, ensuring that it is securely located. DO NOT USE THE PRODUCT WITHOUT FITTING THE HANDGUARD A Starting and Stopping 4 Before starting your Hedgetrimmer. 1. Form a loop in mains cable and push the loop through the hole in the handle as illustrated in Fig. B. 2. To secure, position the loop over the hook and pull back as illustrated in Fig. C. 3. Connect to mains and switch on 4. Remove blade cover/storage holder as illustrated in Fig. D. To start your Hedgetrimmer 1. There are two switch levers fitted to your Hedgetrimmer. 2. Both switch levers need to be held in the operating position (See Fig E) for the product to start. To stop your Hedgetrimmer • Move Hedgetrimmer away from cutting area before stopping. 1. To stop, release one of the switch levers.(Fig F) How to Use How to Use your Hedgetrimmer 1. Inspect area to be cut before each use - remove objects which can be thrown or become entangled in the cutting blades. 2. Always keep the Hedgetrimmer in front of your body. Hold handle firmly with both hands and stand in a secure and stable position. 3. Allow the cutting blades to reach full speed before entering the material to be cut. 4. Always work going away from people and solid objects such as walls, large stones, trees, vehicles etc. 5. If blade stalls, immediately stop the Hedgetrimmer. Disconnect the Hedgetrimmer from the power source and clear jammed debris from the cutting blades. Inspect blades and repair or replace as needed. Top Cutting Use a wide sweeping motion. See Fig. G. A slight downward tilt of the cutting blades in the direction of motion gives the best cutting results. Side Cutting When trimming the sides of the hedge, begin at the bottom and cut upwards (See Fig. H), tapering the hedge inward at the top. This shape will expose more of the hedge, resulting in more uniformed growth. B C D E F G H 5 Caring for your Hedgetrimmer Cleaning (J) 1. Using a soft brush - remove debris from all air intakes and cutting blade. 2. Wipe over surface of your hedgetrimmer with a dry cloth. • IMPORTANT Never use water for cleaning your hed- getrimmer. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts. Lubricating the Cutting Blade For easier operation and longer life, lubricate the cutter blades before and after use. Apply the oil so that it runs between the two blades. See Pic K. At the end of the Cutting Season. 1. Clean your Hedgetrimmer thoroughly. 2. Check that all nuts and bolts are secure. 3. Visually inspect the Hedgetrimmer for any worn or damaged parts, contact your local Service Centre if any parts require replacement. To store your Hedgetrimmer • The Hedgetrimmer blade cover/storage holder is provided with 2 hanging slots for storing the Hedgetrimmer on the wall.(See Pic L) • Ensure the blade cover/storage holder is fitted before storage. 1. The use of 2 number 10 screws (40mm in length) and the appropriate wall fixing plugs is recommended 2. Drill 2 holes 47mm horizontally apart. 3. Fit wall plugs. 4. Fit screw ensuring enough length is avail- able for secure location into hanging slot. • Your mains cable can be stored with the blade cover/storage holder fitted. (Pic M & N) • Store in a dry place where your Hedgetrimmer is protected from damage. J K M N L 5 Caring for your Hedgetrimmer Cleaning (J) 1. Using a soft brush - remove debris from all air intakes and cutting blade. 2. Wipe over surface of your hedgetrimmer with a dry cloth. • IMPORTANT Never use water for cleaning your hed- getrimmer. Do not clean with chemicals, including petrol, or solvents - some can destroy critical plastic parts. Lubricating the Cutting Blade For easier operation and longer life, lubricate the cutter blades before and after use. Apply the oil so that it runs between the two blades. See Pic K. At the end of the Cutting Season. 1. Clean your Hedgetrimmer thoroughly. 2. Check that all nuts and bolts are secure. 3. Visually inspect the Hedgetrimmer for any worn or damaged parts, contact your local Service Centre if any parts require replacement. To store your Hedgetrimmer • The Hedgetrimmer blade cover/storage holder is provided with...

Download now

Please, enter two numbers from picture: