Votes - 3, Average rating: 4 ( )

Manafacture: Makita File size: 936.14 kb File name: Language of manual:

1 (1) Throttle lever (2) Throttle lock button (3)LOCK-OFF switch 6) Hold the holder case firmly by your left hand and give several strong pulls to the starter by your right hand. 7) After the engine is started, open the choke lever fully, checking the engine running condition. Give several strong pulls to the starter. * Immediately after the engine is stopped: Only perform the Nos. 1, 4 and 6 described above. Stopping Return the throttle lever, and when RPM of engine is lowered, push the stop switch to "STOP" position. Engine Wlll stop. Cautions in handling of engine Be sure to use properly mixed fuel. When the engine is cool, warm it up for one to two minutes. The carburetor has been adjusted before shipment. If readjustment is required, consult our agent or dealer. ATTACHMENT AND DETACHMENT OF HANGING BAND Hanging band fitting procedure. (Fig. 1) Detachment (Fig. 2) In an emergency, pull the release belt strongly upward and you can detach the machine from you. Be extremely cautious to maintain control of the machine at this time. Do not allow the machine to be deflected toward you or anyone in the work vicinity. WARNING: Failure to maintain complete control of the machine at all times could result in serious bodily injury or DEATH. (11 Release belt (2)Hanqer (Hanqlnq metal) Fig. 1 Fig. 2 HOW TO OPERATE The nylon cord will feed out automatically to a pre-determined length when you decrease and increase the engine speed of your string trimmer. You do not need to tap the nylon cutting head to let the nylon cord feed out. If the nylon cord does not feed out automatically, decrease the engine speed fully and then increase it fully. The nylon cord will feed out automatically. If the nylon cord still does not feed out sufficiently, perform the same procedures repeatedly until the nylon cord feeds out to the proper length. If the nylon cord is too short to feed out automatically by performing the above procedures, stop the engine and pull out the nylon cord by hand or using pliers more than 40 mm (1-9116"). Then perform the above procedures again. Increase speed Decrease speed Increase speed Lowest speed Full speed Lowest speed Full speed CAUTION: NEVER OPERATE THE ENGINE AT HIGH RPM WITHOUT LOAD. With throttle fully opened and no load, the engine rpm will be very high which can have an adverse effect on the life of the engine. REPLACING THE NYLON CORD The nylon cord can be easily replaced without removing the nylon cutting head from the String trimmer. Always stop the engine before replacing the nylon cord. 1. Loosen the knob in the direction of the arrow engraved on the knob. Remove the knob and the cover. Take out the spool. 2. Remove the remaining nylon cord from the spool. IA (11 Knob (2)Cover 13)Spool 14)Housing (51Eyelet 3. Bend a new nylon cord nearly in half so that there is approx. 120 mm (4-314") of difference between the two ends. I II' = & 73 \ 120 mm 14-314") 4. Hook the bent portion of the nylon cord into the notch in the center plate of the spool. Wind the nylon cords firmly and snugly on the spool in the direction of the "WIND CORD LH @" engraved on the spool. (Note) Do not wind the nylon cords in the opposite direc- tion of the "WIND CORD LH -'' engraved on the spool. Do not overlap or twist the two nylon cords. They will not feed out properly. 5. Wind both nylon cords firmly and snugly until the spool is full to the outer edge of the center plate. Leave approx 120 mm (4.314") of both nylon cords unwound on the spool. Carefully prevent both nylon cords from coming loose on the spool. Pass the end of the shorter nylon cord out through the hole on the side of the rim of the spool and then back into the hole as illustrated. Pass the end of the other, longer nylon cord out through the hole on the opposite side of the spool as illustrated. 6. Pass the end of each nylon cord out through the eyelets on opposite sides of the housing. Place the spool into the housing. Pull the end of nylon cords while pressing down the spool. 7. Adjust the length of nylon cords so that each nylon cord extends approx. 80 mm -120 mm (3-118" - 4-314") out...

Download now

Please, enter two numbers from picture: