Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
Push that bend through the oblong opening, then loop the bend under the cord retaining clips as shown. This will prevent the extension cord from detaching from the line trimmer plug. 5 1. Locate and open sealed bag with 3 screws, 3 split washers, clamp plate #2 and L-pin. (Picture 1) 2. Remove plastic tube and gear case cover #4 from the threaded shaft. 3. Place plastic guard over the gear case flange, and place clamp plate #2 over the plastic guard. Align holes and attach it with three screws to the trimmer attachment assembly. (Picture 3) 4. Place gear case cover #4 onto the gear shaft. (Picture 4) 5. Lock the gear shaft by inserting the supplied pin through the slot in the plastic guard and into the aligned openings in the gear case cover and gear case (Picture 5). Screw in the spool holder with the spool to the gear shaft by turning it counter clockwise (Picture 6). Hand tighten it securely and remove pin. (Picture 7) Picture 1 Picture 2 Picture 3 Picture 4 Picture 5 Picture 6 Picture 7 1 2 3 4 Plastic guard 6 No tools are required to attach the Line Trimmer to the power head assembly. 1. Pull the spring pin up on the adapter of the power head shaft assembly. (Picture 8) 2. Carefully fit the line trimmer drive shaft into the adapter, making sure that the male spline of the inner drive shaft engages into the female spline socket of the power head shaft. (Picture 9) 3. When the drive shaft is properly aligned, the spring pin will drop into the hole on the shaft of the line trimmer attachment. (Picture 10) A click should be heard when completed. 4. Insure two shaft parts are fully engaged by twisting them. Full engagement will prevent shaft rotation. 5. Secure assembly by tightening the knob. (Picture 11) 6. Unit handles can be re-adjusted to the operator’s preference by simply loosening the screws and sliding the handles up or down the shaft. Picture 8 Picture 9 Picture 10 Picture 11 Check the balance of the assembled unit. The handles and shoulder harness have been assembled at the factory and set according to the average size person. This can be adjusted to the operator’s preference by simply loosening the screws and sliding handles up or down the shaft. Re-tighten the screws. 1. With both hands on the handles, push lockout trigger button with your thumb first, and then squeeze trigger. Picture 12 2. Always remember that the tip of the line does the cutting. You will not get better results by moving line deeply into the cutting area. 3. Hold the cutting head of the unit off the ground, and use a sweeping (left to right) motion. Try to control cutting motion with the hip rather than placing the full workload on the arm and hands. 4. The rate of the cutting motion depends on the material being cut: heavy growth will require slower action. 5. Take precautions to avoid wire or dry long-stem plant material from wrapping around the cutting head shaft. This can stall the head. If repeated frequently, this can cause damage of the unit. Lockout Trigger Button Trigger Operator can increase the length of the line when it becomes short, without stopping the engine. In order to do this you have to lightly tap the head of the string trimmer on the bear ground or hard soil while running the engine at full throttle. 1. Clean. 2. Lubricate for rust prevention 3. Store indoors. 7 Replacement spools can be ordered through your Mantis dealer. 1. For safety reasons, 2. For replacement use 0.095 inch (2.5 mm) diametre line. The spool is capable to hold approximately 6 m long line. 3. Hold spool holder and remove spool by turning it clockwise until it stops. Pull the spool and remove old line. 4. Put each end of the new line through the holes in the spool and pull it until one end is approx. 15 cm longer then the other. (Pictures 13 and 14) 5. Hold the spool, so the opening is facing you, and wind up the line tightly and evenly turning the spool in the clockwise direction, separating both line halves by finger as shown below. (Pictures 15 and 16) 6. Insert line into the slots in the spool, and leave approx 15 - 20 cm in of line unwind, then put the ends through the eyelets on the spool holder. (Pictures 17 and 18) 7. Align bosses of the drive with the grooves in the spool, and push it in place. 8. Pull both lines until they come free from the slots in the spool. 9. Hold drum and turn spool counter clockwise until it stops. (Picture 19) Picture 13 Picture 14 Picture 15 Picture 16 Picture 17 Picture 18 Eyelets Picture 19 Holes Approx. 15 cm longer 8 Area Maintenance procedure Frequency Spline male/female connection of the inner drive shaft Inspect/lubricate 1. Remove centre screw, and loosen up other two as shown on the diagram (left). 2. Pull the shaft from the gear housing. 3. Pull and clean internal shaft. 4. Lubricate. 5. Re-install the drive shaft. 20-25 hrs Gear case Inspect/clean debris Remove plug and check level of grease. Add grease. Do not overfill! Use EP2 lithium grease 45-50 hrs Screws/nuts/bolts Inspect/tighten/r...
Other models in this manual:Hair Clippers - Line Trimmer (2.5 mb)