Votes - 2, Average rating: 4.5 ( )

Manafacture: Flymo File size: 436.57 kb File name: d8cd6959-5b20-41ca-9aa2-f4ab1396bad9.pdf Language of manual:

2. Lubricate for rust prevention. Start edging when blade rotates at full RPM, by 3. Store indoor. lowering the blade gently into the ground. Lockout Trigger Button Trigger 2. Thoroughly inspect the surface were the equipment is to be used and remove all stones, sticks, wires, bones and other foreign objects. 3. Before edging, water the area to soften the ground to make edging easier. 4. Plan to edge regularly to make it easier to keep a neat edge and to avoid making more then one pass. 5. Don’t force the blade. Only move forward as the blade will allow. 6. Do not use Edger Attachment to make a new groove into hard ground! 7. You can use the V-notch to indicate postion of the blade tip. V-notch to indicate the position of the blade tip V-notch in the blade guard Blade Service Maintenance Guide Area Maintenance procedure Frequency Spline male/female connection of the inner drive shaft Inspect/Lubricate 1. Remove the side screw, and loosen up other three as shown on the diagram (left). 2. Pull the shaft from the gear housing. 3. Pull and clean internal shaft. 4. Lubricate. 5. Re-install the drive shaft. 6. Do not allow any dirt and dust on the internal drive shaft 7. Do not allow any dirt and dust 20-25 Hrs Lubricate entering into the gear case Gear case Inspect/Clean debris Grease Nipple Use a grease gun to insert lubricant into the grease nipple of the gear case, using EP2 lithium grease. Do not overfill! Remove the gear case cover, and clamping plate before inserting new grease to arrange for old grease to exit Do not allow any dirt and dust entering into the gear case 20-25 Hrs Screws/Nuts/Bolts Inspect/Tighten/Replace Before each use Blade Inspect/Clean/Replace Before each use Area Maintenance Before Every 25 Every 50 Every 100 Note Use Hours Hours Hours Cutting Parts Replace if something is wrong Screws, nuts bolts Tighten, replace Not adjusting screws Blades Oiling Light #10 oil IMPORTANT: Time intervals shown are maximum. Actual use and your experience will determine the frequency of required maintenance. 11 1 2 3 6 4 5 7 8 20 11 12 24 25 9 10 13 14 15 16 23 22 18 19 21 31 26 29 28 30 32 27 42 39 41 40 34 33 35 36 37 38 44 43 49 58 48 47 46 51 54 55 56 57 53 52 56 45 50 62 60 61 59 63 17 Edger “E” System Exploded View Edger “E” System Parts List KEY # DESCRIPTION PART # QTY KEY # DESCRIPTION PART # QTY 1 GEAR CASE ASSEMBLY 331137 1 33 GUARD WITH CLAMPASS’Y 331160 1 2 GEAR CASE 331138 1 34 BLADE GUARD ASSEMBLY 331161 1 3 O-RING 331139 1 35 GUARD METAL 331162 1 4 BEARING 6201Z 331140 1 36 RUBBER DEBRIS GUARD 331163 1 SEAL 331141 1 37 GUARD CLAMPING PLATE 331164 1 6 RING RETAINING 331142 1 38 BOLT M5X12 331519 2 7 SHAFT 331143 1 39 GUARD CLAMP 331165 1 8 GEAR 331144 1 40 BOLT M6X16 331520 2 9 PINION 331145 1 41 WASHER 331521 2 BEARING 609 331146 1 42 BOLT M5X14 331515 3 11 BEARING 609Z 331147 1 43 BLADE 331166 1 12 RING RETAINING 331148 1 44 COVER 331167 1 13 RING RETAINING 331149 1 45 WHEELASS'YWITH ADAPTER 331168 1 14 MOUNTING BOLT 331510 1 46 ADAPTER LOCK WASHER 331511 1 (WHEEL TO MAIN SHAFT) 331169 1 16 FLAT WASHER 331512 1 47 CLAMPING BRACKET HALF 331170 1 17 BOLT M5X12 331513 1 4...

Download now

Please, enter two numbers from picture: