Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
Then you can use the microphone’s remote switch to stop or start recording. 3. Press RECORD to begin recording. Both PLAY and RECORD lock down. Note: To temporarily stop recording, press PAUSE. Press PAUSE again to resume recording. 4. Speak into the external microphone. 5. Press STOP/EJECT to stop recording. Recording from a Connected Audio Source You can record directly from an external audio source, such as a radio, tape deck, or CD player. To make the connection, you need a suitable mono patch cord with a 1/8-inch plug (available from your local RadioShack store). Note: Before you connect an external audio source to the recorder, be sure the source’s and the recorder’s volume controls are set to their minimum settings. Follow these steps to record from an external audio source. Note: If you connected an external microphone, disconnect it. 1. Load a blank cassette tape, or one you want to record over, into the cassette compartment. 2. Connect the external source to the AUX jack. DC IN 6V AUX EAR REM MIC VOLUME External source 3. Start the external audio source and set its volume control to a normal listening level. 4. Press RECORD to begin recording. Both PLAY and RECORD lock down. Note: To temporarily stop recording, press PAUSE. To resume recording, press PAUSE again. 5. Press STOP/EJECT to stop recording. Then stop the audio source. Note: During recording, the speaker is muted. If you want to monitor the recording, use the supplied earphone. 9 14-1115.fm Page 10 Friday, January 8, 1999 10:31 AM TAPE TIPS Recommended Tapes Tape quality greatly affects the quality of the recording. We recommend extended- range or low noise Type 1 regular length (60- or 90-minute) normal- bias cassette tapes. We do not recommend long-play cassette tapes such as C-120s because they are thin and can easily tangle. Erasing a Cassette Tape To record over a cassette tape, simply record as usual. The cassette deck records over the previous recording. To erase the entire cassette tape, insert the supplied erasing plug into the MIC jack and press RECORD. (Be sure you have not connected anything to the AUX jack.) DC IN 6V AUX EAR REM MIC VOLUME If you need to erase an entire cassette, you might prefer using a bulk tape eraser, available at your local Preventing Accidental Erasure Cassette tapes have two erase-protection tabs — one for each side. When a tab is in place, you can record on that side. To protect a recording from being accidentally recorded over or erased, use a screwdriver to remove one or both of the cassette tape’s erase-protection tabs. This prevents RECORD from being pressed. If you later decide to record on a tape A Side A Tab side after you have removed its erase- protection tab, place a piece of strong plastic tape over that side’s erase-protection hole. Be sure you cover only the hole originally covered by the erase-protection tab. A RadioShack store. Caution: Removing the erase-protection tabs does not prevent a bulk eraser from erasing a cassette tape. 10 14-1115.fm Page 11 Friday, January 8, 1999 10:31 AM Restoring Tape Tension and Sound Quality After you play a cassette tape several times, the tape might become tightly wound on the reels. This can cause playback sound quality to deteriorate. To restore the sound quality, fast- forward the tape from the beginning to the end of one side, then completely rewind it. Then loosen the tape reels by gently tapping each side of the cassette’s outer shell on a flat surface. Caution: Be careful not to damage the cassette when tapping it. Do not touch the exposed tape or allow any sharp objects near the cassette. 11 14-1115.fm Page 12 Friday, January 8, 1999 10:31 AM MAINTENANCE Your RadioShack CTR-108 AC·DC Portable Cassette Recorder is an example of superior design and craftsmanship. The following suggestions will help you care for your CTR-108 so you can enjoy it for years. Keep the CTR-108 dry. If it gets wet, wipe it dry immediately. Liquids might contain minerals that can corrode the electronic circuits. Handle the CTR-108 gently and carefully. Dropping it can damage circuit boards and cases and can cause the CTR-108 to work improperly. Use and store the CTR-108 only in normal temperature environments. Temperature extremes can shorten the life of electronic devices and distort or melt plastic parts. Keep the CTR-108 away from dust and dirt, which can cause premature wear of parts. Wipe the CTR-108 with a damp cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the CTR-108. Modifying or tampering with the CTR-108’s internal components can cause a malfunction and might invalidate your CTR-108’s warranty. If your CTR-108 is not performing as it should, take it to your local RadioShack store for assistance. 12 14-1115.fm Page 13 Friday, January 8, 1999 10:31 AM CLEANING THE TAPEHANDLING PARTS Dirt, dust, or particles of the tape’s coating can accumulate on the tape heads and other parts that the ta...