Votes - 3, Average rating: 4.7
(
)
)
|
manual abstract
For your safety, it is necessary to refer to the manual. • DANGEROUS VOLTAGE: Uninsulated dangerous voltage that may be of sufficient magnitude to constitute a risk of electrical shock to persons is present within this product enclosure. • CAUTION: To reduce the risk of electric shock, do not remove cover (or back). Prefer servicing to qualified service personnel. 2 POWER SUPPLY BATTERY OPERATION • Set the FUNCTION switch to the TAPE position. • Open the battery compartment cover. • Insert 6 batteries (UM-1). Please observe correct battery polarities or the set will not work. • Close the battery compartment cover. AC OPERATION • Before the first connecting of the appliance check that voltage indicated on the rating label corresponds the mains voltage in your home. • Plug the corresponding end of cord into the AC socket on the rear of the set. • Insert the plug into power supply. CAUTION: • When the set is only used with AC or is not used for 2 weeks or more, please remove the batteries, to avoid damage to the set from leakage of batteries. • Always unplug the appliance from power supply, when no use long time. • This radio cannot be operated by batteries if the AC power cord is connected to the unit. CONNECTIONS_ HEADPHONE CONNECTING • For private listening, insert 3.5 mm headphone into the stereo headphone jack. • Slide volume control switch to the appropriate level as desired. • When the stereo headphone jack is plugged, speaker will disconnect automatically. FUNCTION_ FUNCTION SWITCH • Position to RADIO for: -Radio reception -Cassette recording from the radio • Position to TAPE for: -Cassette playback 3 -Recording from built-in Condenser Microphone SOUND ADJUSTMENT_ VOLUME The level of sound reproduced by the loudspeaker or Stereo Headphones is adjusted by the VOLUME control. NOTE: During recording, adjusting the VOLUME control only affects the monitor sound and not the content of recording. RADIO OPERATION_ OPERATION • Set Function switch to RADIO position thus the Power LED indicator should light up. • Select your desired broadcasting band with Band switch. • Rotate the Tuning control regulator to receive the desired broadcast. • Adjust the level and quality of sound with Volume control switch. • To turn off the radio, set the Function switch to TAPE position. ANTENNA • For FM reception, adjust the telescopic antenna appropriately to obtain the best reception on the band selected. • The AM signals are picked up through the built-in ferrite antenna. The set should be placed to a position for the best reception. CAUTION: • Do not connect FM antenna to an external antenna. FM AND FM STEREO RECEPTION • Set Band switch FM position, programmer is received in mono mode. NOTE: In particular when stereo signal is weak and much noise are received, it is preferable to receive the programmer in mono. • Set FM Mode switch to FM STEREO position, programmer is received in stereo mode, thus FM STEREO LED should light up. 4 CASSETTE RECORDER OPERATION CONTROLS • STOP/EJECT button During operation, depress to stop all deck operation. Press again to open the cassette door. • FAST FORWARD button and REWIND button Press to rapidly advance the tape in either forward or reverse direction. • PLAY button Press to start playback. • PAUSE button Press to stop tape operation temporarily. Press again to resume tape operation. • RECORD button Press to start recording. PLAY button will be activated automatically. CASSETTE PLAYBACK • Slide the Function switch to TAPE position thus the Power LED indicator should light up. • Press the STOP/EJECT button to open the cassette compartment. • Insert a cassette and push the cassette door to close the cassette compartment. • Press the PLAY button to start the playing. • Adjust the VOLUME control to the desired sound level. NOTE: • Press the PAUSE button to pause the playing. • Press the STOP/EJECT button to stop the playing, press the button again to open the cassette door and you can take out the tape. • When the tape plays to the end, playing will be stopped automatically. RECORDING RECORDING FROM RADIO • Slide the Function switch to RADIO position thus the Power LED indicator should light up. • Tune to the desired station by turning the Tuning control regulator. • Insert a blank cassette into cassette compartment. • Press the PLAY button and RECORD button simultaneously to start recording. • Press the STOP/...