Votes - 4, Average rating: 3.3 ( )

Manafacture: Tascam File size: 994.89 kb File name: 0a191926-e7c7-496f-a0c3-4b19b93f3536.pdf Language of manual:

Pin assignment : Pin 1 is shield (ground), Pin 2 is Hot (+), and Pin 3 is Cold (-). 29. INPUT UNBAL/BAL switch : Selects either the XLR-type or RCA input jacks. 30. OUTPUT XLR-type jacks : Transmit +4 dBm balanced signals to your mixer, monitor amp, etc. Pin assignment: Pin 1 is shield (ground), Pin 2 is Hot (+), and Pin 3 is Cold (-). 31. OUTPUT RCA jacks : Transmit -10 dBV unbalanced signals. 32. INPUT RCA jacks : Accept -10 dBV unbalanced signals. 33. Blank Panel (except 122 MKIII) : Space for mounting an optional balanced amp kit (LA-112). When the LA-112 is installed, you who are using the 112R MKII/112 MKII will have access to the INPUT XLR-type jacks (#28), the INPUT UNBAL/BAL switch (#29) and the OUTPUT XLR-type jacks (#30) as with the 122 MKIII. 34. REMOTE CONTROL connector : This 25-pin D-sub connector is for controlling the transport from the optional remote RC-112R (for 112R MKII) or RC-134 (for 122 MKIII and 112 MKII), or for fader start from a mixer. A 25-pin connector (Part No. 53363571-00) and its jacket (Part No. 5336358100) are optionally available. Fader start (122 MKIII and 112 MKII only) : Pins 22 and 24 are assigned for this function. The transport will toggle Play and Pause, as depicted. 8 PLAY REMOTE CONTROL t PAUSE ->PIN N0.22 jr* -»PIN N0.24 Pin Signal Function 22 FADER START Closed, Play; opened, Pause Y N 23 Not Used - - 24 GND Y Y 25 + 5V Max. 50mA Y Y Y stands for Yes, N for No. Input: To activate a function, the pin must be brought to ground potential for 24 msec or more. REMOTE CONTROL Pin Assignment REMOTE CONTROL li^ilfOOOOOOOOOOOOO)/,«! IÎ4AV oooooooooooo V/^ 112RMKII- 122MKIII/112MKII-^ Pin Signal Function 1 Activates Jhe corresponding transport mode, active at low level Y Y PLAY IN 2 FF IN tt Y Y 3 REWIN tt Y Y 4 PAUSE IN tt Y Y 5 STOP IN tt Y Y 6 REC IN tt Y Y 7 Lets the next deck start playing during sequential play of two decks, active at low level (only when ordered to provide the function). N Y START COMMAND 8 Not Used - - 9 UP/DOWN OUT Indicates the tape travel direction (UP : forward, DOWN : rewind) Y Y 10 END TALLY OUT Indicates either end of the tape is reached, active at low level. N Y 11 Indicates the corresponding mode is activated, active at low level. Y Y F. PLAY TALLY OUT 12 FF TALLY OUT tt Y Y 13 REW TALLY OUT tt Y Y 14 PAUSE TALLY OUT tt Y Y 15 STOP TALLY OUT ft Y Y 16 REC TALLY OUT tt Y Y 17 Activates reverse side play, active at low level. N Y R. PLAY IN 18 Indicates reverse side play mode, active at low level. N Y R. PLAY TALLY OUT 19 REEL PULSE Y Y 20 Not Used - - 21 RTZIN Fast-winds the tape to 00 00, active at low level. Y Y Tally STOP FAST F. PLAY R. PLAY PAUSE REC Timing of Tally Outs Key Operation ! i « „ _ I ______ 1 400m SEC (from Fast mode) | 650m SEC (from Play mode) 1 < ► I I 200m SEC (from Stop mode) 1 800m SEC (from Play mode) t ■ . > ___|_ 1 450m SEC (from Stop mode) ! 1000m SEC (from R. Play mode) I 200m SEC (from Pause mode) 1 I « > i ' ► 1 450m SEC (from Stop mode) 1 1000m SEC (from F. Play mode) | 200m SEC (from Pause mode) | 300m SEC (from Stop mode) • 200m SEC (from Play mode) | REC PLAY 50m SEC (from Play mode) I 450m SEC (from Stop mode) | REC PAUSE 20m SEC (from Pause mode) 300m SEC (from Stop mode) END 600m SEC 9 Basic Operation Recording DOLBY NR MPX FILTER OFF OOB DOC OFF _ON MONITOR INPUT AUTO sjy %X/ — QrausE —“Q-hecoro If you are using the 122 MKIII, first adjust BIAS and LEVEL as per instructions on page 15. 1. Plug the record source into the front or rear input jacks. If you have plugged the record source into the rear jacks, set the INPUT switch (on rear) to the appropriate position. 2. Set the DOLBY NR switch to the desired position, and the MPX FILTER switch to OFF unless you intend to record FM broadcasts. 3. Set the MONITOR select switch to AUTO. 4. Press and hold RECORD and press PAUSE to activate Record Ready mode. 5. Start your record source and adjust the INPUT controls so that the VU meters peak at about 0, and adjust the PHONES control for a comfortable listening level. 6. When everything is ready, press PLAY to start recording. 7. To stop recording, press STOP. Or press PAUSE to temporarily stop recording; to resume recording, press PLAY. Playback DOLBY NR OFF DOB GDC MONITOR INPUT AUTO 1. Set the DOLBY NR switch depending on the tape in use. 2. Set the MONITOR switch to AUTO. 3. To initiate playback, press PLAY. Adjust the OUTPUT and/or PHONES level controls as required. 4. To stop playback, press STOP. Or press PAUSE to temporarily stop playback; to resume playback, press PLAY. Erasing a Tape To erase a cassette tape not by overwriting, set the INPUT controls to 0 and press RECORD and PLAY together. To quickly erase both sides of a tape (except metal tapes), use the optional TEAC E-2A Bulk Eraser. 10 Special Features Autolocator Functions □ ...

Download now

Please, enter two numbers from picture: