About Cassette tape • If the tape is slack tighten it. • If the cassette tape label is peeling off glue it on again. • Don’t use deformed cassette tape. • Don’t place cassette tape on the dashboard etc. where the temperature is high. • Don’t use cassette tape that’s 100 minutes long or longer. — 4— General features General features 4 . SRC FMAM Q/AUD ud ATT / LOUD CLK#3#1 Turning ON the Power Release button Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at least 1 second. Selecting the Source Press the [SRC] button. Source required Display Tuner "TUnE" Tape "TAPE" External disc "DISC"/"CD" Standby (Illumination only mode) "OFF" Volume Clock indicator Clock display Increasing Volume Press the [ u] button. Decreasing Volume Press the [ d] button. indicator SYSTEM Q LOUD indicator ATT indicator — 5— General features General features Attenuator Turning the volume down quickly. Press the [ATT] button. Each time the button is pressed the Attenuator turns ON or OFF. When it’s ON, the "ATT" indicator blinks. • Each setting value is changed with the (page 7). First, select the speaker type with the Speaker setting. • When the System Q setting is changed, the Bass, Middle, and Treble set in audio control replace the System Q values. Audio Control Loudness Compensating for low and high tones during low volume. Press the [LOUD] button for at least 1 second. Each time the button is pressed for at least 1 second the Loudness turns ON or OFF. When it’s ON, "LOUD" indicator is ON. System Q You can recall the best sound setting preset for different the music. 1 Select the source to set Press the [SRC] button. 2 Select the Sound type Press the [Q] button. Each time the button is pressed the Sound setting Display 1 Select the source for adjustment Press the [SRC] button. 2 Enter Audio Control mode Press the [AUD] button for at least 1 second. 3 Select the Audio item for adjustment Press the [FM] or [AM] button. Each time the button is pressed the items that can be adjusted switch as shown below. 4 Adjust the Audio item Press the [ 4] or [ . ] button. Adjustment Item Display Range Bass level "BAS" –8 — 8 Middle level "MID" –8 — 8 Treble level "TRE" –8 — 8 Balance "BL" L15 — R15 Fader "FD" R15 — F15 5 Exit Audio Control mode Flat "SQ-1" Press the [AUD] button. Rock "SQ-2" Top 40 "SQ-3" Pops "SQ-4" Jazz "SQ-5" Easy "SQ-6" Scan of Flat "SCAn" — 6— Speaker Setting Speaker Setting Fine-tuning so that the System Q value is optimal when setting the speaker type. 1 Enter Standby Press the [SRC] button. Select the "OFF" display. 2 Enter Speaker Setting mode Press the [Q] button. 3 Select the Speaker type Press the [ 4] or [ . ] button. Each time the button is pressed the setting switches as shown below. Speaker type Display OFF "SP-F" For the OEM speaker "SP-O" For 6 & 6x9 in. speaker "SP-6" For 5 & 4 in. speaker "SP-5" 4 Exit Speaker Setting mode Press the [Q] button. Clock Display Press the [CLK] button. Each time the button is pressed OFF. When it’s ON, the clock indicator is 1 Select the clock display Press the [CLK] button. 2 Enter clock adjustment mode Press the [CLK] button for at least 2 seconds. The clock display blinks. 3 Adjust the hours Press the [FM] or [AM] button. Adjust the minutes Press the [ 4] or [ . ] button. 4 Exit clock adjustment mode Press the [CLK] button. DSI (Disabled System Indicator) A red indicator will blink on the unit after the faceplate removed, warning potential thieves. 1 Turn the power OFF Press the [SRC] button for at least 1 second. 2 Set the DSI While pressing the [#1] and [#3] button, button. Each time the step 1 and 2 operation OFF. — 7— General features Tuner features General features Tuner features English The faceplate of the unit can be detached and taken with you, helping to deter theft. Removing the Faceplate Press the Release button. The faceplate is unlocked, allowing you to detach it. • The faceplate is a precision piece of equipment and can be damaged by shocks or jolts. For that reason, keep the faceplate in its special storage case while detached. • Do not expose the faceplate or its storage case to direct sunlight or excessive heat or humidity. Also avoid places with too much dust or the possibility of water splashing. Reattaching the Faceplate 1 Align the projections on the unit with the grooves on the faceplate. 2 Push the faceplate in until it clicks. The faceplate is locked in place, allowing AM 4. FM/CRSC SRC #1 – 6 AUTO/AME Band display Preset station number CRSC indicator ST indicator AUTO indicator Frequency display — 8— Tuning Mode Tuning Mode Choose the tuning mode. Press the [AUTO] button. Each time the button is pressed the Tuning mode switches as shown below. Tuning mode Display Operation Auto seek "AUTO 1" Automatic search for a station. indicator Preset station "AUTO 2" Search in order of the stations seek indicator in the Preset memory. Manual — Normal manual tuning control. Putting the station in the memory. 1 Select the ...
)
