Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
Before You Start • Disconnect negative battery terminal. (consult a qualified technician for instructions) • Avoid installing the unit where it would be subject to high temperatures, such as from direct sunlight, or where it would be subject to dust, dirt or excessive vibration. Getting Started • Insert the supplied keys into the slots as shown, and slide the unit out of the mounting sleeve. • DIN mounting procedure: Install mounting sleeve into radio opening, bending tabs to secure. • 2-Shaft mounting procedure: Remove knobs, faceplate and DIN mounting adapters from unit. Install unit into kit or radio opening from behind. Adjust rear shaft nuts to correct depth. Install faceplate and knobs. • Certain applications may require an installation kit and/or wiring harness adapter (sold separately). KEYS MXC22 INSTALLATIOINSTALLATION ® Installation Typical DIN Mounting Typical 2-Shaft MountingKNOBS SHAFT NUTS RADIO OPENING OR INSTALLATION KIT MOUNTING SLEEVE DIN ADAPTERS KNOBS SHAFT NUTS ® MXC22 INSTALLATION Wiring Remote Turn-On Connect to amplifier or power antenna. Insulate wire if not used. RCA Cable (sold separately) Antenna Connector BLUE Rear Preamp Output Connect to amplifier RCA Input GREY Ground Connect to vehicle chassis ground. BLACK Accessory Connect to existing ignition circuit or switched 12 volt source. RED Right Gray/Black (-) Gray (+) Left White/Black (-) White (+) AMP 3 AMP AGC Fuse .5 AMP AGC Fuse Diagram FUSES When replacing fuses, make sure new fuse is the correct type and amperage. Using an incorrect fuse could damage radio. The MXC22 uses one 3 amp AGC fuse (Ignition) and one .5 amp AGC fuse (Remote turn-on) located in-line. MXC22 OPERATIOOPERATION ® Control Locations 12345678910 12345 Power/Volume Band Stereo Indicator FM Indicator Mono/Stereo 869107 Tuning Balance Bass Boost Auxiliary Input Eject/Fast Forward General Operation Power On/Off Turn P PP O OO W WW E EE R RR knob clockwise to turn the unit on. TurnR POWER POWERPOWER knob counter-clockwise until a click is heardPOWER to turn the unit off. Cassette Mode Insert a cassette to begin playback. Tuner Mode Turn POWER POWERPOWER knob clockwise or eject cassette toPOWER begin or resume tuner operation. Auxilary Mode Insert a standard 3.5 mm (line or headphone output) plug into the auxilary input to listen to a portable CD or MP3 player. ® MXC22 OPERATION General Operation (continued) Bass Boost Press BASS to activate and deactivate bass boost curve. Activating this feature will enhance the bass frequencies when listening to music at low volumes. Volume Adjust volume by turning VOL knob clockwise or counter-clockwise. Balance Adjust balance by turning BAL knob clockwise or counter-clockwise. Tuner Operation Tuning FM Mono/Stereo Band Turn TUNE knob to select desired station. Press MO/ST MO/STMO/STMO/ST during FM tuner operation to select mono or stereo reception of the broadcast signal. The FM stereo LED indicator iluminates during FM stereo reception. Press BAND to select between FM and AM bands. The FM LED indicator illuminates when FM is selected. Cassette Player Operation Insert Cassette Eject Fast Forward Insert a standard audio cassette into the cassette slot. The cassette will automatically begin playback. Press the EJECT EJECTEJECTEJECT button all the way in to stop and eject the cassette. The unit will change to tuner mode. Press the EJECT EJECTEJECTEJECT button half way in to fast forward. Press EJECT EJECTEJECTEJECT again to resume playback. MXC22 WARRANTWARRANTY ® Limited One Year Warranty This warranty gives you specific legal rights. You may also have other rights which vary from state to state. Dual Electronics Corp. warrants this product to the original purchaser to be free from defects in material and workmanship for a period of one year from the date of the original purchase. Dual Electronics Corp. agrees, at our option, during the warranty period, to repair any defect in material or workmanship or to furnish an equal new, renewed or comparable product (whichever is deemed necessary) in exchange without charges, subject to verification of the defect or malfunction and proof of the date of purchase. Subsequent replacement products are warranted for the balance of the original warranty period. Who is covered? This warranty is extended to the original retail purchaser for products purchased and used in the U.S.A. What is covered? This warranty covers all defects in material and workmanship in this product. The following are not covered: installation/removal costs, damage resulting from accident, misuse, abuse, neglect, product modification, improper installation, incorrect line voltage, unauthorized repair or failure to follow instructions supplied with the product, or damage occurring during return shipment of the product. What to do? 1. Before you call for service, check the troubleshooting guide in your owner’s manual. A slight adjustment of any custom controls or connections discussed in your instruction booklet may s...