Votes - 2, Average rating: 4
(
)
)
|
manual abstract
The Clip The clip enables you to carry your mini stereo on a belt. This belt clip can be removed by lifting up the lock key while simultaneously pushing it in the direction of the arrow. Headphones You must plug the headphones into the PHONES jack on the side of the unit to hear the radio or cassette tape. Turn the volume down before you put on the headphones and increase the volume to desired level after they are in place. General Controls Volume To adjust the sound level, turn the VOLUME control on the side of the unit. BASS BOOST Turn BASS BOOST (on the side of the unit) ON for enhanced bass effect. Turn BASS BOOST to OFF position for normal bass sound. Using the Radio Display DIGITAL AM/FM PERSONAL STEREO RADIO CASSETTE PLAYER DIGITAL TUNING RADIO ON/OFF RECALL SET RADIO TUNING PRESET STORE BAND AM/FM TUNING + and — buttons BAND button RADIO ON/OFF button RECALL/SET PRESET/STOREbutton button • Press the RADIO ON/OFF button to turn the radio on. The last band and radio station frequency selected appear in the display. • To choose between AM and FM radio bands, press the BAND button. The last station and band selected appear in the display. Note: ST appears in the display when you are receiving a station broadcasting in FM Stereo. The FM radio station must be transmitting in stereo for you to receive the broadcast in stereo. AM stations are received in mono only and ST does not appear in display. • To change the radio station one channel at a time, press and release the TUNING + and — buttons to advance up and down the scale. Automatic Station Seek The Seek feature automatically searches up and down the scale for the next station with a strong signal. Pressing and holding TUNING + or TUNING – for approximately 1 second causes the unit to automatically seek up or down the scale and stop at the next frequency where a strong signal is being received. Storing Radio Stations in Memory You can store 20 stations (10 AM and 10 FM) in memory by using the PRESET/ STORE and RECALL/SET buttons. These are called preset radio stations. To store 1. Make sure the radio is on by pressing RADIO ON/OFF, the display lights. 2. Select the desired band (AM or FM) by pressing BAND. 3. Select the station you want to preset (store in memory) by using the TUNING + and — buttons. 4. Press PRESET/STORE button (MEMO for memory flashes in display for approximately 5 seconds). You must complete steps 5 and 6 within this 5second time period while MEMO is flashing in the display. 5. Press the RECALL/SET button to select the preset channel location. The first time you press the button, CH 1 (channel 1) is selected and appears in the display. Each time you press the button, you advance one channel. 6. Press PRESET/STORE button to store the station as a preset station (MEMO disappears from the display when the station has been successfully stored). The station you selected in step 3 is now stored in the preset CH number shown in the display. Note: Storing a station in memory automatically erases the station that was previously stored in that memory location (preset location). listening to a preset station 1. Make sure the radio is on by pressing RADIO ON/OFF. 2. Select the desired band (AM or FM) by pressing BAND. 3. Press and release the RECALL/SET button until the desired preset station appears in the display. Note: Preset stations will remain in memory for about 30 minutes when replacing batteries. If you have removed the batteries for more than 30 minutes, you may need to store stations in memory again. maximizing am reception For best AM reception, place the unit in a vertical position (with the volume knob and headphone jack facing up) when listening to AM stations. Maximum AM station reception can also be obtained by laying the unit on its back with the belt clip resting on a table or the floor. Using the cassette Tape Player NEW ART REVERSE FWD REW STOPPLAY MODE The Buttons DIR Shows you the direction the tape is playing. F FWD Press and lock to advance tape forward. PLAY Press and lock to play a tape. QUICK REVERSE Press to change tape direction. REV. MODE Select to play both sides of the tape continuously. REV. MODE When started from Side A, unit plays back both sides of the tape and stops. When started from Side B, the unit stops after Side B is finished playing. REW Press and lock to advance tape backward. STOP Press to stop PLAY, F FWD, or REW. Playing a cassette tape 1. Open the tape deck door by using the indexes on the side of the door and pulling the door open. 2. Insert a tape with the exposed tape facing toward the top of the unit. 3. Press REW or F FWD to move tape to the desired starting point. 3. Press and lock the PLAY button on the top of the unit. Important: The cassette tape won’t play if the radio is on. Using Auto Reverse/Continuous Play To continuously play both sides of the tape, set the REV MODE switch to To play each side of the tape once, set the REV MODE switch to Note: You must start playback on side A whe...