|
User manual Panasonic, model RX-FT570
manual abstract
Do not leave it in an automobile exposed to direct sunlight for a long time with the doors and windows closed as this may deform the cabinet. • Avoid cuts, scratches, or poor connections in the AC power cord, as they may result in possible fire or electric shock hazard. Also, excessive bending, pulling or splicing of the cord should be avoided. • Do not unplug the AC power cord by pulling the lead. To do so may cause premature failure or shock hazard. • Do not operate the set on AC mains in a bathroom, as a potential shock hazard may result. • When not in use, disconnect the AC power cord from the AC power outlet. The function selector switch does not separate entire unit from mains even if in “TAPE/E33 ” position. mm. 2 © Headphones Jack (PHONES) ® CD/Line input jacks ({CDj/LINE IN) (3) XBS (Extra Bass System) button (XBS) ® Built-in microphone (MIC) (D Graphic equalizer controls (GRAPHIC EQUALIZER) (D Volume control (VOLUME) ® Deck 1 (For playback) Reverse mode select button (REV MODE *05 m~3) Stop/eject button (BSTOP/EJECT) Fast buttons (^ - FAST- ►►) Playback button ( PLAY) Direction button (DIR) (8) Function selector (SELECTOR) (TAPE/QQ3, RADIO,(CDj/LINE) (9) FM stereo indicator (FM ST) (10} Editing mode selector/beat proof switch (EDITING/B.P) (MIC/I NORMAL/11 HIGH/II) Connections How to connect portable CD player (not included) When listening or recording CD, set SELECTOR to ICDl/ LINE. • When not using the i£D]/LINE IN jacks, disconnect the connector from it. How to use headphones (not included) Reduce the volume level. Connect the headphones to the headphones jack. • Avoid listening for prolonged periods of time to prevent hearing damage. • Speakers are automatically cut off when the headphones are connected. © Deck 2 (For recording and playback) Pause button (H PAUSE) Stop/eject button (0 STOP/EJECT) Fast forward/cue button (/CUE) Rewind/review button (►► /REV) Playback button (< PLAY) Record button (#f~ © Band selector (BAND) © Tuning control (TUNING) © Deck 1 cassette compartment ® Deck 2 cassette compartment © Speaker (Woofer) © Speaker (Tweeter) (OP Handle © Telescopic antenna Battery compartment ® AC socket (AC IN-) L (White) RECORD Listening to Radio Broadcasts Refer to ES. Set SELECTOR to RADIO. Set BAND to the desired radio band. FM STEREO; To receive FM stereo broadcasts (if you have tuned into an FM stereo broadcast, the FM indicator will light.) AM: To receive AM broadcasts If FM stereo reception is poor, set BAND to FM. This will reduce the noise and provide clear reception; however, the broadcast will not be heard in stereo. Use TUNING to tune Into a desired broadcast. I Adjust VOLUME, GRAPHIC EQUALIZER and XBS. The radio can be turned off by setting SELECTOR to TAPE/ Esa XBS (extra bass system) □_ When the XBS button is set to "ON”, the dynamic low frequency ranges are boosted. Adjust the level by using the XBS level control. Using this system with graphic equalizer helps you to get more dynamic sounds. Graphic Equalizer Q It allows you to edit the frequency response of the unit to compensate for room acoustics and other factors which affect frequency response. The overall tone can be altered by adjusting the controls at the three frequency bands; 100Hz, 1 kHz, 10 kHz. For increased amplification of the corresponding frequency band, position the switch towards “+10” marking and likewise towards the “-10” marking to attenuate the corresponding frequency band. If the XBS button is set to “ON1’, the 100 Hz control functions as the XBS level control. Adjust the antennas Q] FM: Pull out the telescopic antenna and adjust its length and angle for optimum reception. AM: Turn the unit in the direction which gives the best results. Listening to Tapes You can use normal tapes only. You can use either deck 1 or deck 2 for tape playback by following the same steps. (This page shows an example using deck 1.) Single tape playback Q Set selector to TAPE/rsraa. Press STOP/EJECT, and then insert the tape. Insert the cassette with the exposed tape facing up. - Playback side Set REV MODE (For deck 1 only) to select desired playback mode in deck 1. : Two side playback mode JL q£> : Repeat two-side playback mode Press PLAY to start playback. Adjust VOLUME, GRAPHIC EQUALIZER and XBS level controls as desired. To stop the playback: Press STOP/EJECT. Auto stop: During playback, when the tape reaches its end, the automatic stop system will release PLAY and automatically turn the unit off. During tape playback, if the deck 1 REV MODE is set to “q£>" position, the automatic stop system does not function. When the tape reaches the end by pressing FAST, the automatic stop system does not function. The tape will stop, but as the motor continues to turn, do not leave the set in this condition. Be sure to press STOP/EJECT. To fast forward or rewind the tape [fj Deck 1 Press —FAST— ►► while the tape is stopped. Deck 2 Press -«...
|
)
