Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
The POWER indicator turns on. 3. Load the cassette tape with its open 20 3. Set FUNCTION SELECTORtoTAPE. VOCAL CHANGER SELECTOR OFF^ON^ CD^_^^PE 4. Press PLAY on the deck 5. Adjust the sound with the controls explained in "Adjusting the Sound" on Page 13. 6. Press STOP/EJECT to stop the tape. Press STOP/EJECT again to open the cassette compartment, then remove the cassette tape. Turn the tape over and press PLAY to play the otherside. Notes: To temporarily stop play, press PAUSE Press PAUSE again to resume play. backward, press FAST-F or REWIND. Press STOP/EJECT when you reach the desired section. To rapidly wind the tape forward or TAPE CARE TIPS Erasing a Cassette Tape Preventing Accidental Erasure Cassette tapes have two erase-protection tabs - one for each side. To protect a recording from being accidentally recorded over or erased, use a screwdriver to remove one or both of the cassette tape's erase-protection Tabs. If you want to record on a tape side after you have removed the erase protection tab, place a piece of strong plastic tape overthat side's erase protection hole. Notes: Be sure you cover only the hole that was originally covered by the erase-protection tab. Removing the erase-protection tabs does not prevent a bulk eraser from erasing a cassette tape. If you no longer want a recording, you can record over it or erase it. To erase a previously recorded section of a tape, simply record over it. To erase the entire cassette tape, record silence by setting FUNCTION SELECTORto TAPE and recording. You can quickly erase both sides of a cassette tape using a bulktape eraser. Cleaning the Tape-Handling Parts Dirt, dust or particles of the tape's coating can accumulate on the tape heads and other parts that the tape touches. This can greatly reduce the performance of the cassette player. After every 20 hours of tape player operation, use a cassette deck cleaning kit or follow these steps to clean the tape-handling parts. 1. Disconnect the AC powercord 2. Open the cassette compartment door. 3. Press PLAY to expose the tapehandling parts. 22 4. Use a cotton swab dipped in denatured alcohol ortape head cleaning solution to clean the record/play heads, pinch rollers, capstans, tape guides, and erase heads. 5. When you finish cleaning, press STOP/EJECT and close the cassette compartment doors. Then reconnect power. Restoring Tape Tension and Sound Quality After you play a cassette tape several times, the tape might become tightly wound on the reels. This can cause playback sound quality to deteriorate. To restore the sound quality, fastforward the tape from the beginning to the end of one side, them completely rewind it. Then loosen the tpe reels by gently tapping each side of the cassette's outer shell on a flat surface. Caution: Be careful not to damage the cassette when tapping it. Do not touch the exposed tape or allow any sharp objects nearthe cassette. 23 USING OPTIONAL COMPONENTS Warning: To protect your hearing and prevent damage to the karaoke system, an audio source and/or and audio component, always set their volume controls to the lowest settings before turning themon. 6. To turn off the system, press POWER The POWER indicator lights turn off Then turn off the audio component. LISTENING THROUGH ANOTHER AUDIO COMPONENT If you connected an audio component (such as PA system) follow these steps to listen to the karaoke system's sound 1. Set FUNCTION SELECTOR to CD I 2. Press POWER to turn on the system The POWER indicator turns on. 3. Turn on the audio component. 4. Play a cassette, CD, or CD+G in the 5. Adjust the sound with the controls explained in "Adjusting the Sound" on 24 RECORDING A CASSETTE TAPE RECORDING YOUR VOICE WITH MUSIC You can become a recording star! The system lets you record your voice on a blank or reusable tape as record from the CD. Recording Tips: Tape quality greatly affects the quality of the recording. We recommend Extended Range or Low-Noise Type 1 tape. We do not recommend long-play cassette tapes, such as C-120s, because they are thin and can easily tangle in the cassette mechanism. For low-noise, wide-range recordings, use normal-biastape. Before recording, be sure the tape you are using has its erase-proection tabs in place. See "Preventing Accidental Recording automatically stops when the tape reaches the end. To record on the other side, turn over the tape. Follow these steps to record your voice along with musicfrom a CD/CD+G. 1. Load a blank tape, or one that you want to record over, into tape deck, with the side you want to record on facing out, and the full reel to the left. 2. Follow Steps 1-10 in "Singing with a CD/CD+G or Cassette Tape" on Page 10-11. 3. Press RECORD to begin recording. RECORD and PLAY both lockdown. Note: Press PAUSE to temporarily stop recording. Press PAUSE again to resume recording. 4. Press STOP/EJECT to stop recording. RECORD and PLAY release. 25 TROUBLESHOOTING If you h...
Other models in this manual:Audio Players - MKS 3001 (2.75 mb)
Audio Players - MKS 3001 (2.75 mb)