Votes - 4, Average rating: 3.5
(
)
)
|
manual abstract
This will permit direct access for easier exhaust connection. Slide the end of the exhaust duct underneath the clips on the back of the dryer and secure with duct tape or a hose clamp. DRYER EXHAUST TO SIDE OR BOTTOM OF CABINET If you wish to exhaust your dryer to the side or bottom of the cabinet, order exhaust kit 14-A003, available from your GE supplier. Transition Ducting Clip Duct NOTE: We strongly recommend using rigid metal exhaust duct. • For straight-line installation, connect the dryer exhaust to the wall using duct tape. Wall Side Dryer Side 28 Installation Instructions FINAL SETUP 1 LEVEL THE DRYER 2 PLUG IN DRYER Stand the dryer near the final location. Place a level against the side and bottom of the dryer door frame and use the four leveling legs to level your dryer. Lower Raise Ensure proper ground exists before use. 29 Installation Instructions FINAL SETUP (cont.) DRYER STARTUP Press the POWER button. SERVICING WARNING – Label all wires prior to disconnection when servicing controls. Wiring errors can cause improper and dangerous operation after servicing/installation. For replacement parts and other information, refer to the Owner’s Manual for servicing phone numbers. NOTE: If the dryer has been exposed to temperatures below freezing for an extended period of time, allow it to warm up before pressing POWER. Otherwise, the display will not come on. The dryer is now ready for use. 30 Installation Instructions REVERSING THE DOOR SWING (if desired) REMOVE FILLER PLUGS Open the door and remove the filler plugs opposite the hinges. 1 REMOVE DOOR • With the door completely open, remove the BOTTOM screw from each hinge on the dryer face. • Insert the screws about halfway into the TOP holes, for each hinge, on the opposite side (where you removed the filler plugs). Apply firm pressure to get the screw started in new holes. 2 REMOVE HANDLE Remove the screws holding the handle and two spacers. 3 Rear of Door REVERSE DOOR CATCH Remove the door catch and filler plate. Install them on opposite sides of the door. 4 Filler Plate Catch • Loosen the TOP screw from each hinge on the dryer face halfway. With one hand holding the top of the door and the other hand holding the bottom, remove the door from the dryer by lifting it UP and OUT. 31 Installation Instructions REVERSING THE DOOR SWING (cont.) REVERSE HANDLE Install the handle on the opposite side of the door. Rear of Door 6 REMOVE HINGES AND REHANG DOOR Remove the hinges from the door and install them on the opposite side with the hinge pin toward the outside of the door. 6 REMOVE HINGES AND REHANG DOOR (cont.) Insert the door on the opposite side of the opening by moving the door IN and DOWN until the top hinge and the bottom hinge are resting on the top screws inserted in Step 2. Remove the remaining screws from the side of the opening from which the door was removed. With these screws, secure each hinge at the bottom. Tighten the two top screws of each hinge. Reinsert Opposite Side the plastic plugs on the side from which the door of Door was removed. 32 Before you call for service… GEAppliances.com Troubleshooting Tips Save time and money! Review the chart below first and you may not need to call for service. Problem Possible Cause What To Do Dryer won’t Control panel is asleep • This is normal. Press POWER. operate Dryer is unplugged • Make sure cord is plugged securely into a working outlet. Controls are not set properly • Make sure the cycle was set correctly, close the lid and press START. Fuse is blown/circuit breaker • Check house circuit breakers/fuses. Replace fuses or reset is tripped breaker. NOTE: Electric dryers use two fuses or breakers. Electronics need to be reset • Unplug dryer, wait 2 minutes, plug back in and press POWER. START was not pressed after • Press START. a cycle was set Door was opened during the • Close the door and reset cycle, to the beginning if necessary. dry cycle Press START. Dryer is too cold • If the dryer has been exposed to temperatures below freezing for an extended period of time, allow it to warm up before pressing POWER. Otherwise, the display will not come on. Normal Operating Sounds The following are normal sounds you may hear: Sound Description Thumping noise when • If the dryer has not been used for an extended period of time, you may hear a thumping noise drum rotates from temporary flat spots on the drum support rollers. The noise will go away after use. Consumer SupportTroubleshooting InstallationInstructions 33 Consumer Support Troubleshooting Tips Operating Instructions Safety InstructionsInstallationInstructions GE Dryer Warranty. (For customers in the United States) Staple your receipt here. Proof of the original purchase date is needed to obtain service under the warranty. All warranty service provided by our Factory Service Centers, or an authorized Customer Care® technician. To schedule service, on-line, visit us at GEAppliances.com, or call 800.GE.CARES (800.432.2737). Please have serial num...
Other models in this manual:Boats Accessories - PROFILE DPGT650 (2.03 mb)