Login:
Votes - 2, Average rating: 4.5 ( )

User manual Attwood, model 5080

Manafacture: Attwood
File size: 480.46 kb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


For Sidelight Pairs, mark and drill a 3/4" (19mm) diameter hole on each side deck of the boat, equal distance from the bow. (Figure 3) 4. Thread wire leads and base stem into hole. Align centerline mark with straight-ahead position and mark location of screw holes. 5. Remove base and drill 1/8" (3mm) pilot holes for both screws. 6. Bring 12V DC (+) and (-) wires up through deck hole. Connect wires using waterproof crimp on butt joint connectors. 7. Activate light to verify proper operation. 8. Apply a thin bead of non-silicone sealant into groove on underside of base to prevent water from entering hull or cabin. Do not allow sealant to enter the lens bayonet channels. 9. Align and fasten base with stainless screws. Do not over tighten. 10. Replace lens helmet flush on base and turn clockwise until click is heard and felt. (Figure 3) Figure 3 On Off • • • • • • Lens Helmet "O" Ring Lens Bayonet Channels Centerline Mark 1/8" (3mm) Pilot Holes 3/4" (19mm) Dia. Hole INSTALLATION, RAISED BASE MOUNT All-Round Lights 1. Place light in position as shown in Figure 1. Important: Before drilling, be sure that light will shine within 5° of horizontal when boat is floating. 2. Mark and drill 3/8" (10mm) diameter hole (Figure 4; Sidelight lens is shown). 3. Thread wire leads and base stem into hole. Mark location of screw holes. Proceed to Step 4 below. Bi-Color Sidelights and Sidelight Pairs 1. Place sidelight(s) in position as shown in Figure 2. Important: Before drilling, be sure that sidelights will shine straight ahead and within 5° of horizontal when boat is floating. 2. For Bi-Color Combination light, mark and drill 3/8" (10mm) diameter hole on the boat centerline. For Sidelight Pairs, mark and drill 3/8" (10mm) diameter hole on each side deck of the boat, equal distance from the bow. (Figure 4) 3. Thread wire leads and base stem into hole. Align lens division with straight-ahead position and mark location of screw holes. 4. Remove base and drill 1/8" (3mm) pilot holes for both screws. 5. Bring 12V DC (+) and (-) wires up through deck hole. Connect wires using waterproof crimp on butt joint connectors. 6. Activate light to verify proper operation. 7. Apply non-silicone sealant to underside of base. 8. Align and fasten base with stainless screws. Do not over tighten. (Figure 4) Figure 4 On Off • • Lens Helmet "O" Ring Notch • 1/8" (3mm) 3/8" (10mm) Dia. Hole • • Pilot Holes FINAL WIRING CAUTION: Power source must be positive 12V DC only. All positive (+12V DC) wires must be fused to protect the circuit. Attwood Pulsar Navigation Lights require a 1-amp fuse. Failure to make proper connections and fusing will void product warranty. 1. Neatly thread wires to dash avoiding any areas where abrasion or snagging may occur. 2. Use waterproof crimp on butt joint connectors to attach wires to a switch on the dash that allows for two-position operation - one for running lights and one for anchor lights. Test lights for proper operation. (Figure 5) Figure 5 • 12V DC...

Other models in this manual:
Boats Accessories - 5045 (480.46 kb)
Boats Accessories - 5940 (480.46 kb)
Boats Accessories - 5980 (480.46 kb)
Boats Accessories - 5040 (480.46 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category