Votes - 2, Average rating: 4.5
(
)
)
|
manual abstract
Make connections according to WIRING INSTRUCTIONS below. 3. Feed the positive (red or gray) and negative (black) wires through the hole in base and lead them below deck. 4. Lower the housing onto the base. Seat the housing so the base tabs fit in the housing grooves and the base screw mount aligns with the housing screw hole. 5. Replace the stainless steel cover, then fasten it with the Phillips-head screw. WIRING INSTRUCTIONS The power supply must be 12-volt DC ONLY. Use crimp-type marine-grade connectors with suitable waterproof insulation. Protect all connections with suitable materials. NOTE Failure to make proper connections and fuse the light properly will void the product warranty. CAUTION Polarity is important. If wiring is mis-connected the LED light will not operate. 1. Connect wires to fused power source: (See Figure 3). • Connect the (-) black wire to the negative (-) wire from the 12-volt supply. • Connect the (+) gray or red wire along with proper fuse and switch to the positive (+) 12-volt supply. • Fuse must be 1-amp. 2. Note that navigation rules require sidelights to be operated separately from anchor lights. Use either two switches or a single switch with three positions for off/anchor/running. Figure 3 (pos) (neg)(pos) 12V DC 1-Amp Fuse Switch Green Red (Starboard) (Port) ATTWOOD LIMITED 10-YEAR WARRANTY Because of the longevity of Attwood’s LED lighting technology, Attwood offers a limited 10-year warranty on this LED lighting product. See Product Catalog or attwoodmarine.com for details. © 2007 Attwood Corporation 1016 N. Monroe Street, Lowell, MI 49331-0260 Figure 2 3 3 ® Series 3500 Feux de cote a DEL de 1 NM et 2NM en acier inoxydable Lumiere de proue bicolore a DEL : Paire de feux de cote a DEL : CONSERVEZ CES DIRECTIVES Formulaire n° 69425 Rev. A 07-04 Feux de cote de 1 NM (serie 3520 et 3530) Pour les bateaux mesurant jusqu’a 12 metres (39,4 pieds). Conforme aux exigences USCG CFR 183.810, ABYC A-16 et a toutes les normes applicables selon les tests d’Imanna Laboratories du 22/2/2007. Visibilite d’un mille marin. Lumiere de proue bicolore de 2 NM Pour les bateaux mesurant jusqu’a 20 metres (65,6 pieds). Conforme aux exigences USCG CFR 183.810, ABYC A-16 et a toutes les normes applicables selon les tests d’Imanna Laboratories du 6/3/2007. Visibilite de deux milles marins. Feux de cote de 2 NM Pour les bateaux mesurant jusqu’a 50 metres (164 pieds). Conforme aux exigences USCG CFR 183.810, ABYC A-16 et a toutes les normes applicables selon les tests d’Imanna Laboratories du 6/3/2007. Visibilite de deux milles marins. REQUIS POUR L’INSTALLATION • Tournevis cruciforme • Perceuse et meches : • 9 mm pour le trou de passage des fils • Foret pilote pour les vis de montage • Deux vis a tete cylindrique bombee n° 10 en acier inoxydable (non comprises) EMPLACEMENT 1. Positionnez le(s) feu(x) sur une surface horizontale (a plus ou moins cinq degres) du plat-bord ou du pont. 2. Pour installer la lumiere bicolo...
Other models in this manual:Boats Accessories - 3530 (63.95 kb)
Boats Accessories - 3500 Series (63.95 kb)
Boats Accessories - 3520 (63.95 kb)
Boats Accessories - 3550 (63.95 kb)