Votes - 3, Average rating: 4.7 ( )

Manafacture: Furuno File size: 2.74 mb File name: Language of manual:

The target appears "pushed" or "pulled" near the picture center. The range to objects are shown at wrong distances. (1) Target pulled (2) Correct (3) Target pushed outward Examples of wrong and correct sweep timings 1. Transmit on the shortest range, then adjust the gain and the A/C SEA. 2. Visibly select a target that creates a straight line (harbor wall, straight piers). 3. Open the Installation menu and select Timing Adjust. 4. Press the ENTER key to show the setting window. 5. Press • or .. to make straight the target selected at step 2, then press the ENTER key to finish. Manual MBS Adjustment Reduce the main bang (black hole), which appears at the display center on short ranges, as follows. 1. Transmit the radar on the shortest range. 2. Open the Installation menu and select MBS Adjust. 3. Press the ENTER key to show the setting window. 4. Press the cursor pad to reduce the main bang (between 0 and 25). 5. Press the ENTER key to finish. Video Initial Adjustment After you complete the automatic installation setting, tune the video signal if necessary. 1. Transmit the radar and set the radar as follows. • Gain : 85 to 90 • A/C Sea : zero • A/C Rain : zero • Echo Average : OFF • Noise Rejector : OFF • Interference Rejector : 2 2. Open the Installation menu and select Video Init Adjust. 3. Press the ENTER key to show the setting window. 4. Press the cursor pad to show some white noise on the display. The setting range is 0 to 31. A large value increases the gain. 5. Press the ENTER key to finish. Note: If the display unit is used as a remote display, set "Input Source" to "Slave". Do the Video Initial Adjust as shown in the above procedure. The echo presentation on the remote display is like the presentation on the main display. ARPA Adjustment During the sea trial, adjust the threshold level of the ARPA for short pulse, middle pulse and long pulse. • Default setting is 2. • If the ship echoes are difficult to acquire at the setting 2, set to 1. • If the ARPA symbol moves to other echo at the setting 2, set to 3. 4. OPTIONAL EQUIPMENT 4.1 ARP Kit ARP-11 The ARP kit provides automatic radar plotter functions to this radar. Necessary parts Name: ARP kit Type: ARP-11 Code no.: 008-523-050 For details, see the packing list attached to the kit. 1. Unscrew 12 screws and five connector nuts at the rear of the display unit. Remove 12 screws. Remove five connector nuts. Do not remove this connector nut. Rear panel of Display unit 4-2 2. Lift the cover slowly and open it as shown below. 3. Mate P107 on the ARP board to J214 on the 03P9474 board and fasten the ARP board with four screws. 03P9474 J214 Cover ........................................ .............................................. ........................................ ARP board Comfirm that rubber gasket is set securely in the groove around the panel. 4-3 4. Reassemble the display unit. .......... .......... ...... ........ ...................................... ............ ...... ...... ...... Torque 2.94±0.29 Nm Torque 0.78±0.08 Nm Torque 0.78±0.08 Nm (12 pcs) ............ 4-4 4.2 Connection of Buzzer and/or Remote Display You need the cables shown below to connect the optional external buzzer and remote display. • Two-way cable MJ-A10SPFW0001+R • MJ-A7SPF0007-050C • MJ-B24LPF0010-xxx+R (xxx: 100, 200 or 300) External buzzer When a target enters (exists) in the guard zone, the optional external buzzer gives a loud alarm. Type:OP03-21 Code no.:000-030-097 Attach the two-way cable and MJ-A7SPF0007-050C cable to the OPTION port at the rear of the display unit. See the above figure. 1. Cut the NH connector at the end of the external buzzer cable to an acceptable length. 2. Solder the external buzzer cable to the MJ-A7SPF0007-050C cable as shown below. Before you solder the cores, cut the heat-shrink-tube in half and set the tubes to the cores of the cable. Solder the cores, then set the tubes on the soldered point. 3. Fasten the buzzer with the double-sided tape or two self-tapping screws (3x15 or 3x20, local supply). Name Type Code No. Qty Comment 1 Buzzer PKB42SWH2940 000-153-221-10 1 One NH connector attached 2 Cable tie CV-70N 000-162-185-10 4 3 Heat-shrink- tube 3x0.25 BLK 000-165-283-10 1 40 mm 4 Double-sided Tape 9760 000-800-851-00 1 25 mm x 25 mm OPTION Remote Display External buzzer MJ-A7SPF0007-050C (5 m) MJ-10P MJ-10P MJ-7P MJB24P Display unit RDP-152 Connection Port MJ-A10SPFW0001+R * (0.2 m) MJ-B24LPF0010-xxx+R (10/20/30 m) (xxx: 100..200 or 300) *: This cable is not required to connect the remote display only. Red Black External buzzer MJ-A7SPF0007-050C Solder Cut other cables off, and wrap here with tape. 1/ 1 PACKING .LIST RDP- 152-1835-E/ C.RDP- 152-1935-E/C.RDP- 152-1945-E/C 03HD-X-9852-1 NAME OUTLINE Q'TYDESCRIPTION/CODE № . .. . UNIT .. . 1 RDP-152-1835/19**-E/ C DISPLAY UNIT 000-014-616-00* * . .. SPARE PARTS .. . SPARE PARTS 1SP03-12200 000-086-965-00 . .. ACCESSORIES NAME OUTLINE DESCRIPTION/CODE № Q'TY .. . . . OPERATOR'S MANUA...

Download now

Please, enter two numbers from picture: