Votes - 2, Average rating: 4
(
)
)
|
manual abstract
PUB.No. PUB.No.PUB.No. OME-13090 OME-13090OME-13090 ( (( DAMI DAMIDAMI ) )) CSH-83/84 CSH-83/84CSH-83/84 Your Local Agent/DealerYour Local Agent/Dealer FIRST EDITION FIRST EDITIONFIRST EDITION : :: NOV. NOV.NOV. 1997 19971997 F FF : :: APR. APR.APR. 05,2002 05,200205,2002 *00080806600* *00080806600* *00080806600* *00080806600**00080806600* * 0 0 0 8 0 8 0 6 6 0 0 * * 0 0 0 8 0 8 0 6 6 0 0 ** 0 0 0 8 0 8 0 6 6 0 0 * *OME13090F00* *OME13090F00**OME13090F00* *OME13090F00* *OME13090F00**OME13090F00* * O M E 1 3 0 9 0 F 0 0 * * O M E 1 3 0 9 0 F 0 0 ** O M E 1 3 0 9 0 F 0 0 * SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS WARNING Do not open the equipment. Hazardous voltage which can cause electrical shock exists inside the equipment. Only qualified personnel should work inside the equipment. Immediately turn off the power at the switchboard if water leaks into the equipment or something is dropped in the equipment. Continued use of the equipment can cause fire or electrical shock. Contact a FURUNO agent for service. Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. Do not place liquid-filled containers on the top of the equipment. Fire or electrical shock can result if a liquid spills into the equipment. Immediately turn off the power at the switchboard if the equipment is emitting smoke or fire. Continued use of the equipment can cause fire or electrical shock. Contact a FURUNO agent for service. Make sure no rain or water splash leaks into the equipment. Fire or electrical shock can result if water leaks in the equipment. WARNING Keep heater away from equipment. A heater can melt the equipment’s power cord, which can cause fire or electrical shock. Use the proper fuse. Fuse rating is shown on the equipment. Use of a wrong fuse can result in equipment damage. Do not operate the equipment with wet hands. Electrical shock can result. CAUTION Do not exceed 18 knots when operating the equipment and do not exceed 16 knots when lowering or raising the transducer. The transducer may become damaged. The zinc block attached near the transducer must be replaced yearly. The junction between the transducer and main shaft may corrode, which can result in loss of the transducer or water leakage inside the ship. Do not use the equipment for other than its intended purpose. Use of the equipment as a stepping stool, for example, may result in personal injury or equipment damage. Replace the monitor when the picture becomes difficult to see. The average life of the monitor is about 10 years. Replace it when the picture becomes difficult to see, to protect vision. A warning label is attached to the equipment. Do not remove the label. If the label becomes soiled or illegible, contact a FURUNO agent or dealer. TABLE OF CONTENTS FOREWORD A Word to CSH-83/84 Owners ............................................................................................... vii Features................................................................................................................................... vii System Configuration ............................................................................................................viii CONTROL DESCRIPTION Control Layout on Display Unit and Remote Control Box ...................................................1-1 Main Panel.............................................................................................................................1-2 Sub Panel 1 ............................................................................................................................1-4 Sub Panel 2 (data setting window) ........................................................................................1-5 Remote Control Box..............................................................................................................1-8 OPERATIONAL OVERVIEW Turning the Power On/Off.....................................................................................................2-1 Adjusting Screen Brilliance, Control Panel Backlighting .....................................................2-1 Lowering the Transducer .......................................................................................................2-1 Selecting a Display Mode......................................................................................................2-2 Selecting a Display Range.....................................................................................................2-3 Setting the Tilt Angle .............................................................................................................2-3 Adjusting the Gain.................................................................................................................2-7 Measuring Range and Bearing to a Target.............................................................................2-7 FINE TUNING THE PICTURE Eliminating Unwanted Feeble Echoes..........................
Other models in this manual:Boats Accessories - CSH-83 (1.8 mb)