Votes - 4, Average rating: 3.3
(
)
)
|
manual abstract
Attention! Carefully read through these instructions prior to installation and commissioning. Attention! Priere de lire attentivement la presente notice avant l'installation et la mise en service. Attentie! Lees deze instructies voor de installatie en ingebruikname aandachtig door. Attenzione! Prima dell'installazione e della messa in esercizio, leggete attentamente e completamente queste istruzioni. Atencion! Lea atentamente estas instrucciones antes de la instalacion y puesta en marcha. Bem.rk! L.s denne vejledning opm.rksomt igennem inden installationen og idrifttagningen. IT DA D NL F ENG ES ENG ENG Contents 1 Scope of Application 2 Specifications 3 Product Liability/Warranty 4 Safety Information 5 Installation 6 Operation 7 Care and Maintenance 8 Spare Parts List 1 Scope of Application This Sliding Carriage is intented for use with the Elekta Beckum Spindle Moulder models TF900/TF904. It is used for working across the endgrain of timber having a square or rectangular crossection. - Please observe all relevant safety regulations for the use of spindle moulders applicable in your area. When in industrial use in the U.K. use of this accessory falls under the 1974 Woodworking Regulations. In the interest of health & safety of the machine user we recommend you study and follow these regulations. We would also draw your attention to the booklet "Woodworking Machines Regulations 1974-Guidance on Regulations" ref. L4 /ISBN 0118855921) published by HSMO. 2 Specifications Table size: 280 x 525 mm Carriage travel: 700 mm Fence: adjustable 45° through 90° Graduation: 1° Carriage guides: 4 rollers, on ball bearings Max. allowable workpiece weight: 20 kg Mounting: quick-action locks Workpiece clamping: quick-action clamp 3 Product Liability/Warranty This product carries a 12 month manufacturer warranty under the prevailing legal provisions, which may vary from country to country. The warranty period begins with the date of the original purchase by the end user. Proof of purchase should be retained and must be presented in the event of a warranty claim. This warranty excludes and does not cover defects, malfunctions and failures caused by natural wear, overload, unreasonable use or failure to provide reasonable and necessary maintenance. In case of a defect notify your dealer or Elektra Beckum distributor, who will decide how to handle your claim. Warranty claims can only be taken care of by your Elektra Beckum dealer or authorized service centre. This product or any of its parts should not be altered or changed from standard specifications. The user of this product shall have the sole responsibility for any malfunction which results from improper use or unauthorized modification from standard specifications, faulty maintenance, damage or improper repair by anyone other than qualified person approved by Eleketra Beckum or its representatives. 4 Safety Instructions Feeding the workpiece with a sliding carriage is considered semi-mechanical feed. The cutterheads and moulding tools used must be approved for mechanical feed. Always perform such moulding operation with the cutterhead running at counterrotation, i.e. the cutterhead is turning against the direction of feed of the workpiece. Always have the workpiece firmly secured to the sliding carriage's table with the clamps provided. 5 Installation Fit the two crosshead plates (370/371) to the machine housing. Use 4 each cup square neck bolt M 6x20 flange nut M 6 Reinstall backstop plate. Hook roller carriage extrusion (358) with both extrusion brackets (319 + 320) onto the crosshead plates. If it is a tight fit remove some paint from the slots in the extrusion brackets. Secure roller carriage extrusion by fixing the rear extrusion bracket (319) to the crosshead plate (371), to prevent unhooking. Use 1 each hexagen head bolt M 6x16 hexagon nut M 6 Place sliding carriage table onto traversing saddle and secure with the lock levers. Loosely fit two cup square neck screws M 6x20 with washer O6.4, spring washer O6 and hexagon nut M6 to the two holes in the front of the carriage table. Remove the front backstop plate (360) and slide traversing saddle onto the roller carriage extrusion. Slide link bracket extrusion on the heads of the just fitted cup square neck screws. At this stage do not tighten the screws. The carriage table should be set approx. 0.5 mm higher than the machine table. Set with setting screws B. Loosen screw Alignment: Set roller carriage extrusion parallel to the machine table with both front and rear set- Den Klemmhebel mit Unterlegscheibe durch den Schlitz der Kulissenschiene fuhren und den Stellgleiter aufschrauben. C B A holding rear extrusion bracket (319/371 and 320/370) to bracket before turning setting screw B and tighten after setting. Make trial cut to verify proper setting. After setting is completed, tighten all 4 nuts (408) M8 (A). ting screws C. It does not matter if the carriage table is higher or lower than the machine table. After successf...