Votes - 4, Average rating: 4
(
)
)
|
manual abstract
10 -12 16 16 14 12 12 -16 14 12 Not Recommended • OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. • STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired orotherwise impaired. • CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should becarefully checked to determine that it will operate properly and perform its intended function. Check foralignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired orreplaced by an authorized service center. Do not use tool if switch does not turn it on and off. • REPAIRS AND SERVICE. Repairs, maintenance and any adjustments not specified in this manual should beperformed by Black & Decker authorized service centers or other qualified service organizations, always using identical replacement parts. • USE OF ACCESSORIES AND ATTACHMENTS. The use of any accessory or attachment not recommended foruse with the tool could be hazardous. Note: Refer to the accessory section of this manual for further details. SAFETY WARNINGS AND INSTRUCTIONS: DOUBLE INSULAT I O N Double insulated tools are constructed throughout with two separate layers of electrical insulation or adouble thickness of insulation between you and the tool’s electrical system. Tools built with double insulationare not intended to be grounded. As a result, your tool is equipped with a two prong plug which permits youto use extension cords without concern for maintaining a ground connection. Double insulation does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool. REPLACEMENT PARTS: When servicing use only identical replacement parts. Repair or replace damaged cords. SAFETY WARNINGS AND INSTRUCTIONS: POLARIZED PLUGS Polarized plugs (one blade is wider than the other) are used on equipment to reduce the risk of electric shock. When provided, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. SAFETY WARNINGS AND INSTRUCTIONS: CIRCULAR SAW S •KEEP GUARDS IN PLACE AND IN WORKING ORDER. Never wedge or tie lower guard open. Check operation of lower guard before each use. Do not use if lower guard does not close briskly over saw blade. CAUTION: If saw is dropped, lower guard may be bent, restricting full return. Snagging the lower guard on a surface below the material being cut can momentarily reduce operator control. The saw can lift partially out of the cut increasing the chance of blade twist. Ensure there is sufficient clearance under the workpiece. •LOWER GUARD When necessary to raise lower guard manually, use the retracting handle. •KEEP THE BLADES CLEAN AND SHARP. Sharp blades minimize stalling and kickback. The use of dull and/or dirty blades can increase the saw loading causing the operator to push harder which promotes twisting. DANGER: KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from blades. Never place hands in front or behind the path of the blade while cutting. Do not reach underneath work while blade is rotating. Do not attempt to remove cut material when blade is moving. CAUTION: Blades coast after turn off. When cut is completed, allow blade to stop before removing saw. The telescoping lower guard will close as the saw is lifted. •SUPPORT LARGE PANELS Large panels must be supported as shown (Fig. 1) in this manual to minimize the risk of blade pinching and kickback. When cutting operation requires the resting of the saw on the workpiece, the saw shall be rested on the larger portion and the smaller piece cut off. •USE RIP FENCE Always use a rip fence or straight edge guide when ripping. •USE ONLY CORRECT BLADES AND BLADE ASSEMBLY COMPONENTS IN MOUNTING Do not use blades with incorrect size holes. Never use defective or incorrect blade washers or bolts. Follow blade assembly procedures. •ADJUSTMENTS Before cutting be sure depth and bevel adjustments are tight. •SUPPORT AND SECURE THE WORK PROPERLY Insure that the material to be cut is clamped (Fig. 3) and solidly supported and balanced on a strong, stable and level work set-up. Support the work so that the wide portion of the saw shoe is on the portion of the material that doesn’t fall after the cut is made. Never hold cut off piece by hand (Fig. 4). Kickback from blade pinch can result. Keep both hands on saw at all times. •STAY ALERT AND EXERCISE CONTROL Keep body positioned to one side of blade. Always maintain a firm grip and control of saw with both hands. Do not change hand grip or body position while saw is ...
Other models in this manual:Saws - 7358 (613.06 kb)
Saws - 7359 (613.06 kb)
Saws - 7360 (613.06 kb)