Votes - 1, Average rating: 4
(
)
)
|
manual abstract
Children should not be allowed to operate this unit. ■ PLAN AHEAD 1. Dress in a long-sleeved shirt and long pants. Wear protective gloves and shoes. Eye and ear protection should be worn at all times. Do not wear loose clothing, jewelry, short pants or sandals. Do not go barefoot. 2. Guard against hazardous situations at all times. Warn adults to keep pets and children away from the work area. Establish a safe method for gaining your attention during operation. Be careful if you are approached. 3. Do not operate the unit when you are tired, ill or upset; or if you are under the influence of alcohol, drugs, or medication. 4. Inspect the work site before each use. Remove all debris and objects that could be thrown, become entangled in the cutting head, or cause damage during operation. ■ HANDLE FUEL WITH CAUTION 1. Eliminate all sources of sparks or flame (including smoking, open flames, or work that could cause sparks) in the area where fuel is mixed, poured, or stored. 2. Mix, pour, and store fuel in an approved, marked container and in a well ventilated area. 3. Be sure to stop the engine before refueling the unit. 4. Do not smoke while handling fuel or while operating the unit. 5. Wipe up all spills before starting the engine. Move at least 10 feet (3 meters) away from fuel and refueling site before starting the engine. ■ OPERATE YOUR UNIT SAFELY 1. Inspect the entire unit before each use for worn, loose, or damaged parts. Do not use until the unit is in proper working order. 2. Keep the handles free of oil and fuel. 3. Never start or run the engine inside a closed room or building. Exhaust fumes contain dangerous carbon monoxide. 4. Keep the engine idle speed adjusted properly so that the cutting head comes to a complete stop when trigger is released. 5. Be sure to stop the engine before refueling, inspecting or leaving the unit unattended. 6. Always use both hands to hold the unit. 7. Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit. ■ MAINTAIN YOUR UNIT PROPERLY 1. Disconnect the spark plug before performing all maintenance except for carburetor adjustment. 2. Use only recommended, genuine replacement parts to avoid creating hazard and/or voiding your warranty. 3. Wear protective gloves when handling or performing maintenance on metal blades. 4. When transporting or storing the unit, drain fuel from the fuel tank. 5. Do not store the unit or fuel in a closed area where fuel vapors can reach an open flame from hot water heaters, furnaces, and so on. 6. Store the unit in a dry area out of the reach of children. 7. All engine service, other than those explained in this manual, should be performed by competent service personnel. Improper service to the muffler and flywheel could cause serious accidents. ( 2 ] PARTS LOCATION & SPECIFICATION SPECIFICATIONS Model Name: Overall Dimensions (L X W X H): Dry Weight: Transmission: Reduction Ratio: Number of cutters per blade: Engine Type: Displacement: Max. Output: Max. Torque Fuel: Fuel Tank Capacity: Carburetor: Ignition System: Spark Plug: Starting: Stopping: Standard Accessory: Optional Accessory: ^Specifications are subject to change (3) SGC2300DL 74.4 X 9.1 X 8.7 in. 14.0 lbs. Automatic centrifugal clutch, gear reduction and crank mechanism 7.87 20 2-stroke air-cooled gasoline engine 22.5(1.37) cc(cu. in.) 0.9 at 7,000 rpm HP 8.95 at 5,500 rpm in-lbs Mixture (Gasoline 32: 2-cycle oil 1) 1.07 pints Diaphragm type, Rotary valve Transistor controlled flywheel magneto Champion RCJ-6Y Recoil starter Primary circuit short-circuiting Service tool kit Shoulder strap without notice.) SETUP 3. Hook the cable end into the hole of the throttle lever. A. Engine 1. Install the engine to the driveshaft so that the cylinder head and the stop switch may come on the same side. 2. Using attached four bolts, secure the connection firmly with equal force (Torque: 25 in-lbs) A Never use any screws other than those specified by the manufacturer, or the engine can get loose, resulting in a hazardous event. B. Throttle Control 1. Loosen two screws and remove the control bracket from the shaft casing. 4. Install the control bracket to the shaft casing. 5. Connect the switch wires (Black ->• Black/Red Red). C. Blade Cuttercase 2. Pass the throttle cable through the holes on the bottom of the rear grip. A The blade has very sharp edges. Be sure to use protective gloves whenever handling it. 1. Remove the fastening screw (long) and the lock screw (short) from the cuttercase. 2. While aligning the locking holes (cuttercase hole, spacer hole, and shaft casing hole) install the cuttercase assembly to the shaft casing. If it will not bottom, twist the case slightly back and forth. 3. Align the locking holes and make sure that the locking screw (short) is fastened to the bottom by hand, then secure it with wrench. Í4) Note: If the locking screw is ti...
Other models in this manual:Saws - SGC2300DL (1.54 mb)