Votes - 2, Average rating: 5 ( )

Manafacture: Festool File size: 2.41 mb File name: Language of manual:

Secure the guide rail in this position with the two screws [5-1] and tighten using the hexagon wrench. Lower the guide rail onto the support unit so that the groove in the underside of the guide rail fi ts on to the pin [4-5] of the support unit. The guide rail is properly attached when only a very slight lateral pressure is necessary for the pin to engage into the guide rail. The defl ector [6-1] is pushed onto the end of the guide rail. Close the rotary knob [6-2]. The defl ector prevents the extraction hose and the power cable from catching on the guide rail. Step 5: Attaching the pre-set profi le setting rail The rail can be attached at any point along the clamping edge of the bench and is so versatile, it can be used as a cross stop or a longitudinal stop. NOTE: Before attaching, make sure that the V groove on the fence is not dirty. Open the clamping jaws using the knob [7-2]. Place the fence with guide rail [7-1] onto the clamp rail from above. Secure the clamp segment using the knob [7-2]. 6-1 6-2 6 7-1 7-2 7 8 Step 6: Calibrating angle Check the angle setting of the pre-set profi le setting rail before starting work. Align the guide rail fi rst of all [Fig. 8]. Align the guide rail at right angles to the pre-set profi le setting rail. If an angle of 90° is not possible, slide a support unit on the guide rail until the angle is correct. Secure the guide rail. NOTE: Slide the relevant stop [4-3] along the table profi le to retain the setting permanently. If required, the pre-set profi le setting rail can also be aligned in relation to the perforated top provided the necessary clamps (accessories) are available. Insert the clamps [9-1] and [9-2] as shown in Fig. [9] and move the stop ruler [9-3] to a 90° position. If the stop ruler does not rest evenly against the clamps: Loosen the screws [9-4] and the rotary knob [7-2]. The retaining pin must be engaged in the 90° notch. Set the angle at 90° in relation to the clamps and tighten the screws. Step 7: Adjusting the pre-set profi le setting rail Risk of injury! Always use the fence in a fi xed position and do not use to slide the workpiece along! Risk of injury! Make sure that all rotary knobs on the fence are tightened before starting work. The fence can be adjusted in the following ways: 9-1 9-2 9-3 9 9-4 8 90° 10-1 10-2 10-3 10-6 10-4 10-5 max. 5 mm Adjustment parallel to the bench edge: Loosen the rotary knob [10-4]. Adjustment at right angles to the bench edge: Loosen the rotary knob [10-4]. Adjusting the stop ruler [10-5] lengthways Loosen the rotary knob [10-1]. The stop ruler can be moved to a lower position for thin workpieces or a higher position for thicker workpieces. Angle adjustment using the scale Loosen the rotary knob [10-2] and lift the retaining pin [10-3]. The rotary retaining pin engages in the most common angle positions. Step 8: Adjusting the guide rail in relation to the workpiece For sawing and routing applications, the guide rail can be lowered via [1-2] and [1-4] so that the rail rests evenly on the workpiece. The workpiece and the rail are retained securely. A support piece of suitable thickness is placed centrally under the guide rail between the workpiece and the support unit [1-2] so that the guide rail does not tilt when narrow workpieces are machined. Step 9: Adjusting the cutting depth for sawing [Fig. 11] Always make sure that the cutting depth setting is correct in relation to the workpiece thickness. We recommend setting a cutting depth to a maximum of 5 mm more than the workpiece thickness to protect the profile frame from damage. 10 MFT/KAPEX: Mounting the KAPEX The perforated top on the MFT/KAPEX was specially designed for mounting the KAPEX KS 120. Risk of injury! Before starting work, make sure that the machine is secured properly Risk of injury! Respect the maximum workpiece dimensions. Mount the machine on the MFT/KAPEX as shown in Fig.[12]. Secure the machine to the MFT using clamps. Maintenance Turning the perforated top When worn on one side, the perforated top can be turned over. Loosen the four screws in the corners underneath the bench. Accessories, tools For safety reasons, only use original Festool accessories and tools! The accessory and tool order number can be found in the Festool catalogue or on the Internet under 12 Warranty Conditions of 1+2 Warranty You are entitled to a free extended warranty (1 year + 2 years = 3 years) for your Festool power tool. Festool shall be responsible for all shipping costs during the first year of the warranty. During the second and third year of the warranty the customer is responsible for shipping the tool to Festool. Festool will pay for return shipping to the customer using UPS Ground Service. All warranty service is valid 3 years from the date of purchase on your receipt or invoice. Festool Limited Warranty This warranty is valid on the pre-condition that the tool is used and operated in compliance with the Festool operating instructions. Fe...

Download now

Please, enter two numbers from picture: