Login:
Votes - 2, Average rating: 5 ( )

User manual DeWalt, model DW5100

Manafacture: DeWalt
File size: 2.17 mb
File name: 97e68761-b5ff-49f0-90fd-5218933e3cf7.pdf
Language of manual:enesfr
Free link for this manual available at the bottom of the page



manual abstract


5. Slide the two legs into the holes in the saw shoe as shown in Figure 4. INSTALL RIP GUIDE IN THIS DIRECTION FIG. 4 D C C 6. Adjust the front and rear scales to read the same measurement. WARNING: Both front and rear scales MUST BE set at the same rip width or serious personal injury due to kickback may occur. 7. Securely tighten front (C) and (D) rear locking screws at desired rip width. DW5100 DUAL PORT RIP GUIDE Safety Warnings WARNING: For your own safety, read the saw instruction manual before using any accessory. Failure to heed these warnings may result in personal injury and serious damage to the saw and the accessory. When servicing this tool, use only identical replacement parts. WARNING: • Use only with DWS535, DWS535T circular saws. Use of this rip guide with other saws may increase the risk of kickback and injury. • Before making a cut be sure that both the front and rear scales are set at the same rip width. Using the rip guide with the scales set at different rip widths may cause blade binding and increase the risk of kickback. • After installing the rip guide on the saw or after moving the guide to change the rip width setting, check the operation of the lower guard before starting the saw and making a cut to make sure that the rip guide does not affect proper guard operation. • After installing the rip guide on the saw or after moving the guide to change the rip width setting, securely tighten both the front and rear locking screws on the saw foot plate to prevent the rip guide from moving while cutting. Ripping Ripping is the process of cutting wider boards into narrower strips – cutting grain lengthwise. Hand guiding is more difficult for this type of sawing and the use of the DW5100 dual port rip guide is recommended. Assembly 1. Loosen knob on the under side of the rip guide. 2. Slide leg (A) horizontally until the leg stops (Fig. 1). A FIG. 1 3. Rotate leg (B) until it stops at 90° then repeat with leg (A) as shown in Figures 2 and 3. B FIG. 2 FIG. 3 90° 90° DEWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD 21286 (OCT09) Part No. N053885 DW5100 Copyright © 2009 DEWALT The following are trademarks for one or more DEWALT power tools: the yellow and black color scheme; the “D” shaped air intake grill; the array of pyramids on the handgrip; the kit box configuration; and the array of lozenge-shaped humps on the surface of the tool. DW5100 DISPOSITIF DE GUIDAGE A DOUBLE ACCES Consignes de securite AVERTISSEMENT : pour votre securite, lire le manuel de l’utilisateur de la scie avant l’utilisation de tout accessoire. Tout manquement a ces avertissements augmente les risques de dommages corporels, et les risques d’endommager serieusement la scie et ses accessoires. Lors de l’entretien de cet outil, n’utiliser que des pieces de rechange identiques. AVERTISSEMENT : • A utiliser seulement avec les scies circulaires DWS535 et DWS535T. L’utilisation de ce dispositif de guidage avec d’autres scies peut augmenter les risques de rebonds et de dommages corporels. • Avant toute coupe, s’assurer que les reglettes avant et arriere sont reglees sur la meme largeur de coupe. Le fait d’utiliser le dispositif de guidage alors que les reglettes sont ajustees sur des largeurs differe...


Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category