Login:
Votes - 3, Average rating: 3 ( )

User manual Royal Sovereign, model RSH-1151

Manafacture: Royal Sovereign
File size: 582.71 kb
File name: bd0f8486-24aa-435d-ac88-6433fadeb8a3.pdf
Language of manual:en
Photos and specs  Royal Sovereign  RSH-1151
Free link for this manual available at the bottom of the page



manual abstract


(range 32~320°F or 0~160°C) 3. SPEED: To change speed of the rollers by pressing button, then up or down arrow. (range 1 through 9) 4. MEMORY: To recall or change presets. To recall the settings, press MEMORY then up or down arrow. To save the settings, set desired temperatures and speeds then press the MEMORY button twice. (stores up to 9 different settings) 5. C/HOT: To change the mode from hot to cold or cold to hot lamination. In cold mode, the speed defaults to 2 (speed 1~ 9 settings) and stand-by function is disabled. 6. T-CHECK: To check current upper and lower roller temperatures.Display automatically returns to the previous settings after 5 blinks. 7. ST/BY: To change to stand-by mode (temperature will automatically reset (80°C). While in this mode, all the buttons on the control panel are disabled. Press ST/BY mode button to resume normal operation. NOTE: Auto stand by mode and auto power off mode -Stand by mode:If no activity is made within 2 hours after automatically switch into stand by mode. -Auto power off mode:If the machine is in stand by minutes the machine will automatically power off. -If any activity is made while in stand by or auto to it's previous stage. 8. REV: To reverse the rollers. Must press and hold the button to activate. 9. STOP: To stop the rollers from turning. 10. RUN: To start the rollers . 11. RESET : To reset the substrate and Press and hold RESET button 12. FAN: To activate the cooling 13. MEAS: To display the substrate Press button again 7 8. ROLLER NIP SETTING Speed (Ft/min, M/min) SPEED # HOT COLD 1 1.3 (0.4) 1.5 (0.5) 2 2.1 (0.7) 2.8 (0.8) 3 3.0 (0.9) 4.3 (1.3) 4 3.6 (1.1) 5.4 (1.7) 5 4.3 (1.3) 6.9 (2.1) 6 5.4 (1.7) 7.6 (2.3) 7 6.6 (2.0) 9.5 (2.9) 8 8.2 (2.5) 10.5 (3.2) 9 9.8 (3.0) 13.1 (4.0) No. Inches Metric (mm) 1 Lamination Lamination 2 1/25" 1 3 3/16 ~1/4" 5-7 4 3/8 ~1/2" 10-13 5 3/5" 15 NOTE: If you don't want to laminate,please place the pressure lever to the "Open position(NO.5)". 8 RSH-1151/1651 9 10 9. USING FOOT PEDAL AND REMOTE CONTROL 10. USING CROSS CUTTER USING FOOT PEDAL Place the foot pedal on the floor in front of the machine. Once all correct settings are displayed, you may use the foot pedal to operate the laminator for “Hands Free Operation.” To activate the machine, press the foot pedal once and then release. Repeat to stop the rollers. The cross cutter is located in the rear exit table of the unit. 1. After lamination, move the cutter approximately to the center of the completed application at the desired point of detachment (Figure 1). 2. Grasp film with one hand, press the cutter downward into the application and slide it first to one end of the application, then to the other end to complete the cut (Figure 2 & 3). USING REMOTE CONTROL(OPTION) Located on the left hand side of the rear of the laminator, to use press: 1. RUN : To activate the rollers. 2. STOP : To stop the rollers from turning. 3. REV : To reverse the rollers. Press and hold the button (useful for jams or mis-feeds of media). 1 2 3 Figure 1 11. USING SLITTER (OPTION) 1. Adjust the left and/or right slitters by loosening the slitter adjuster knob (located between the front and rear rollers.) Figure 1 2. Activate the slitter by turning the slitter knob(located on the left side of the machine) counterclockwise. Figure 2 3. Once you activate the slitter then you can begin lamination. Figure 3 4. To deactivate the slitter turn the slitter knob clockwise. Figure 4 NOTE: When the slitter becomes dull break off the blade. Pull the lock back,then pull the slitter out,and push the lock back to previous position. Figure 5 Figure 2 Figure 3 CAUTION When the slitters are not in use please keep the slitters positioned at the far left and right side to avoid injury. Figure 1 Figure 2 Figure 3 Figure 4 Figure 5 RSH-1151/1651 12. LOADING FILM 13. THREADING FILM Royal Sovereign films are wound with the adhesive side facing the inside of the roll (adhesive in). Loading films to upper and lower film shafts: (See page 5 for assistance with parts identification. ) 1. Adjust the auto grip to fit to the film and tighten the auto grip screw (Figure 1 & 2). Figure 1 Figure 2 2. Remove the upper and lower film shafts from the machine and load the films (Center the upper and lower films on the shaft). Note the direction of the adhesives on the lower and upper films (Figure 3 & 4). Figure 3 Figure 4 3. Load the upper and lower film shafts on the machine (Figure 5 & 6). Figure 5 Figure 6 11 13.1 Lamination and Encapsulation Thermal Lamination 1. Turn the power switch on (“I” position) . Power switch is located in the rear of the unit on the left side. 2. Complete the steps on “Loading films to upper and lower film shafts” - Page 11 3. Set the rollers temperature to the recommended film temperature. 4. Take off the Paper Guide and the Front Table. 5. Pull down the upper film over the Safety Cover to the lower film; align and center the lower film to upper film (Figure 1). 6. Rewind the upper film back unti...

Other models in this manual:
Laminators - RSH-1651 (582.71 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category