Votes - 3, Average rating: 4.3
(
)
)
|
manual abstract
o lagliate ¡J toofdo eccedenle. 0 la lasciate come contorno ádeslVo per la firma. SET-UP CONT. OPERAZIONE CONT. Mounting with GBC Designer Frames™ GBC Creative Foils1 MOUNTING WITH GBC DESIGNER FRAMES™ 1. Select the MOUNT mode, and wait for the ready indicator. The MOUNT default is 150' C (302* F), Speed 1. 2. Select a GBC Designer Frame that is larger than the document to be mounted. Designer Frames come with a hardboard, face film with a protective carrier film, and mounting film. If necessary, trim mounting film to the same size as the material to be laminated. 3. Place the mounting film on the backside of the material to be laminated. 4. Lift or “open” the face film from the hardboard, and position the material to be laminated (and the mounting film) onto the mounting board. 5. Replace or “close" face film. 6. Start laminating. Hold the Designer Frame and its contents tightly when feeding it into the laminator, so that the original is not pushed out upon feeding between the rollers. 7. When the Designer Frame exits the rear of the laminator, then carefully rub a finger against a front comer to remove the protective carrier film. Be careful not to separate the layers of the board. OTHER APPLICATIONS: GBC CREATIVE FOILS™ 1. Select 150' C (302‘ F) and speed 3, and wait for the READY indicator. 2. Place GBC Creative Foil color-side-out over output from a toner-based laser printer or photocopier. When printing various colors on the same original piece, arrange the different colors and secure with the stickers included with the Creative Foils. 3. Insert the document and foil into a carrier and laminate. 4. When the item exits the rear of the laminator, then remove the document from the carrier and remove the excess foil. MONTAGGIO GBC DESIGNER FRAMES™ I.Selezionare i! sistema MOUNT, ed aspettare l'indicazione READY. La pre-impostazione MOUNT é a 150°C, velocitá 1. 2. Scegliete un telaio GBC piü largo del documento da montare. II telaio si ottiene con un cornice rígida, inserite il film nel carrier, e montatelo. Se necessario, rifilate il film alla stessa dimensione del materiale da plastificare. 3. Mettete il film montato sul retro del materiale da plastificare. 4. Sollevate il film dal telaio, e posizionate il materiale da plastificare (e il film di montaggio) sul telaio di montaggio. 5. Riabbassate il film. 6. Iniziate a plastificare. Tenete ben stretto il telaio e il suo contenuto quando Io inserite nella plastificatrice.. cosi che l'originale non viene spinto fuori al momento deH'inserimento tra i rulli. 7. Quando il telaio esce dal retro della macchina, con cura rimuovete il carrier. ALTRE APPLICAZIONI: GBC CREATIVE FOILS™ 1. Selezionate la temperatura a 150°C e la velocitá a 3, e aspettate l'indicazione READY. 2. Mettere il foglio con il lato colorato verso I'esterno. Quando stampate diversi colori sullo stesso originale, sistemate i diversi colori e assicurateli con gli stickers inclusi nei fogli GBC. 3. Inserite il documento e il foglio colorato nel carrier e plastificate. 4. Quando il documento esce dal fondo della macchina, rimuoverio dal carrier e rimuovere anche il foglio colorato. GBC Transfer Paper trasferirnenlo 1. Seleilonale la temperatura a 127"C e la V&gjSitä s4,e aspettate I'jodlc^one RE:ADV Se la macchina é stata usasa per i| plastificazione a calda, cunltollate la tnmperaiura corre nte tram Up il iasto SET-UP CQHT. OPE RAZIOME dont. GBC SOFT TOUCH POUCHES ™ GBC SOFT TOUCH POUCHES™ 1. Select 127 C (260‘ F) and speed 4, and wait tor the READY Indicator. If the machine has been used Id Hot Lamination, then check ihe current temperature by pressing Ihe MEAS key. It the lemperalure is above 1 10' C (£30' F). then wait for the lempefalure to decrease. 2. Start laminating. 3. When the pouch exits Ihe rear ot the laminatoit then care!Lilly rub a finger against a front corner to remove the protective carrier film, GBC TRANSFER PAPER 1 Copy Dr print black and color copies, üülot laser copies and offset prints onto G^C Translei Paper, Cut the transfer paper lo ihe desiied size and shape. 2. Select ISO' C (302' F), Speed 1 to 5. and wail lor ihe READY indicator. If the material onto which the image is to be transferred is heavy, then use Speed 1. It the material is Nrvqj Irani le, use Speed 5. The material may be cloth, melal, paper, ar plastic. Transferring may also be done onto the msidt? of GBC Nn-Heat puuches to make roaltac hable decals, or onio she outside of GBC No-Heal Laminate lo ma¡