Login:
Votes - 3, Average rating: 4.3 ( )

User manual Royal Sovereign, model RSS Series

Manafacture: Royal Sovereign
File size: 708.46 kb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


Power switch is located in the rear of the unit on the left side. 2. Complete the steps on “Loading films to upper and lower film shafts” - Page 11 3. Set the rollers temperature to the recommended film temperature. 4. Take off the Paper Guide and the Front Table. 5. Pull down the upper film over the Safety Cover to the lower film; align and center the lower film to upper film and tighten the two lower bolt core screws (Figure 1). 6. Rewind the upper film back until the film aligns with the Safety Cover. 7. Thread the film over the Upper Idle Bar and underneath the Safety Cover until the film rests on the upper roller (Figure 2). 8. Carefully pull up the laminate from the lower roll around the back side of the lower idler (Caution: lower roller may be hot). 9. Tack the lower film to the upper film that is resting on the main roller (Figure 3). Figure 1 Figure 3 12 ¿RS§3SUp 10. Reinstall the Front Table and the Paper Guide, and close the Safety Cover. 11. Adjust the nip setting to 1/8" (3mm). 12. Insert and push the leader boards on each end until boards reach the front nip point. 13. Push the Run button. 14. Push the leader boards between the pair of main rollers (Figure 4). 15. Press the Run button and adjust the supply roll tension knobs by rotating clockwise or counterclockwise. Turn it until the supply roll films have some resistance (the tension varies depending on the film thickness; the thicker the film the more tension is required) (Figure 5). 16. Press Stop button when the leader board has completely exited the rear of the unit. 17. Use the Cross Cutter to cut the leader board from the web (see page 9). 18. Peel off the film from the board for reuse. 19. Set the roller nip setting to the appropriate position for the lamination or encapsulation application. 13 RSS, RSR, RSH Series 13.2 Decaling TAKE UP DEVICE COLD FILM TAKE UP DE ^ COLD FILM RELEASE LINER HOT METAL ROLLER - UPPER IDLE BAR UPPER IDLE BAR PAPERBACK N. -ROLLER V-LOWER IDLE BAR LOWER IDLE BAR 1. Follow the steps in the “Loading Film” procedure by loading the upper shaft with pressure sensitive film, e.g. (Royal Print-Pro Film) and lower shaft with pressure sensitive mounting adhesive films, e.g. (Royal Sovereign White-Mount or Clear-Mount). 2. Pull the upper laminate under the upper idle bar and separate the release liner from the laminate. 3. Tape the release liner to the Take-Up Paper Core and allow the laminate to hang over the main rollers. 4. Pull up the mounting adhesive and tack it to the laminate hanging over the rollers (do not use the Lower Idle Bar). 5. Reinstall the Front Table and the Paper Guide and close the Safety Cover. 6. Turn on the upper take-up motor. 7. Adjust the nip setting to 1/8"(3mm). 8. Insert and push the leader board until board reaches the nip point. 9. Press the Run button and adjust the supply roll tension knobs by rotating clockwise or counterclockwise. Turn it until the supply roll films have some resistance (the tension varies depending on the thickness of a film; the thicker the film the more tension is required). 10. Press Stop button when the leader board has completely exited the rear of the unit. 11. Use the Cross Cutter to cut the leader board from the web (see page 9). 12. Set the roller nip setting to the appropriate position for the lamination application. 14 Sovereign 13.3 Mounting 1. Lay the decaled image face down on a flat surface. Carefully peel back and put a crease alon...

Other models in this manual:
Laminators - RSH Series (708.46 kb)
Laminators - RSH-1650 (708.46 kb)
Laminators - RSR Series (708.46 kb)
Laminators - RSR-1050 (708.46 kb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category