Votes - 2, Average rating: 4
(
)
)
|
manual abstract
. Insert the plug of the laminator into a mains power socket. . Provide a firm location for the appliance. . Set the selector switch for hot and cold lamination i to "HOT ". . Set the foil thickness switch o to the desired foil thickness (80 or 125 microns). The red ON/OFF indicator lamp u will now glow. The laminator heats itself up to its operating temperature. • As soon as the green indicator lamp "Ready" y glows, the laminator has reached its operating temperature. • Attainment of the operating temperature is indicated by the lighting up of the green LED indicator lamp "Ready" y. For a more uniform laminating result we recommend, especially for thinner foils (below 125 Micron) and after adjustment to a different foil thickness, to first wait an additional 2-3 minutes before beginning with lamination. . Lay the document to be laminated into a laminating pouch of the appropriate size. • Make certain that all corners of the document have at least two millimetres of space to the edge of the laminating pouch, as shown in Fig. 1. Make certain that you use only one pouch for laminating. First open it up, as shown in Fig. 2. Fig. 1 • For information about the lamination process, please read section 10. Fig. 2 - 5 9. Preparing for cold lamination • If you have previously performed hot lamination: After hot laminating, allow the laminator to cool down completely before beginning with cold lamination. Remember, the rollers inside the laminator will still be hot. These can damage the laminating pouch and the document to be laminated! . Insert the foil guide rails q in the designated holes on the rear of the laminator. . Pull out the document supports s so that the documents can be pulled in straight into the slot for manual foil feed t. . Insert the plug of the laminator into a mains power socket. . Provide a firm location for the appliance. . Set the selector switch for hot and cold lamination i to "COLD". • Take note: For cold lamination, ALWAYS place the foil thickness switch o at 125 microns. The red ON/OFF indicator lamp u and the green indicator lamp "Ready" y now glow. . Place the document to be laminated into a laminating pouch of the matching size. • Make certain that all corners of the document have at least two millimetres of space to the edge of the laminating pouch, as shown in Fig. 1. • Make certain that you use only one pouch for laminating. First open it up, as shown in Fig. 2. • For information about the lamination process, please read section 10. 10. Lamination process .Lay the laminating pouch onto the pouch guide q. Lay the right or left edge of the laminating pouch against the pouch format lock r (closed side leading). Slide the pouch format lock r together until the selected format size is reached. This prevents the laminating pouch from being pulled in at an angle. • Should the laminating pouch be pulled in at an angle, use the "Anti-Blocking Funktion" as described in chapter 11. .Now slide the laminating pouch slowly into the slot for manual pouch input t. .When you have slid the laminating pouch several centimetres into the slot t, it will start to be pulled in automatically. Release the laminating pouch as soon as you notice it being pulled in automatically. • Ensure there is at least 45 cm of open space in front of the laminator. If you do not, the laminating pouch will not be completely ejected from the laminator after lamination. This could damage the laminated pouch. .The finished laminated pocket is now ejected from the foil slot a of the laminator. Only after hot lamination: .Remove them immediately from the appliance, as hot foil pockets can still be easily deformed. Place them on a flat surface to cool down. • To improve the lamination result, you can weigh down the still hot foil bag with a book, a file folder or other heavy, smooth object. This will give it a smooth and flawless surface. - 6 .If you do not want to start another lamination process, turn the foil thickness switch o to ABS (OFF) and withdraw the plug from the mains power socket. 11. Anti-Blocking Switch (ABS) At the start of the lamination process, the pouch may be pulled in at an angle or jam itself inside the appliance. . Turn the anti-blocking switch (ABS) o to the position ABS. • The laminate pouch is not pulled any further in. . Remove the laminate pouch. . Turn the anti-blocking switch (ABS) o back to the desired foil thickness. . Re-start the lamination process. 12. Trimming function Should you wish to use the trimming function on the pouch guide q, dismantle the pouch guide q. . If necessary, fold the documents supports s down. . Adjust the cutter attachment d so that it forms a straight face with the foil guide rails q. . Slide the cutting head e to the end stop (the cutting head e can be slid to both ends of the cutting rail w). . Flap the cutting rail w upwards with the rounded grip and position the document on the pouch guide q. Restrain the document by sliding the pouch format locks r together until the...