Votes - 5, Average rating: 3.8 ( )

Manafacture: Grizzly File size: 100.84 kb File name: g5938_m.pdf Language of manual:

com THE WARRANTY ON THIS PRODUCT IS COMPLETELY UNCONDITIONAL AND FREE OF “ RED TAPE” ! Should you find a manufacturing defect with one of our wheels we will replace it free of charge or refund your purchase price, including shipping. CALL TOLL FREE: 1- 866- 419- 4879 or 1- 877- 725- 2197 RECOMMENDED SPEED 3000 - 3600 RPM Page Four 8x75x625GWWBor8x75x625SWWB Broughttoyouby: Phone: (800) 523-4777 Fax: (800) 438-5901 com This wheel is a replacement wheel ( either gritted or slotted) for the eight inch Razor Sharp Edgemaking System. It will put a polished razor sharp edge on your knives and tools in just seconds. Gritted Wheel is Grizzly Part #G5938 Slotted Wheel is Grizzly Part #G5939 THE WHEEL IN THIS PACKAGE IS EIGHT INCHES BY THREE- QUARTERS OF AN INCH WITH A FIVE EIGHTHS- INCH ARBOR HOLE. The installed bushing converts it to a one- half inch arbor hole. Simply remove the bushing for use on a five- eighths inch arbor. This eight inch wheel is intended for use on a six inch buffer or bench grinder, turning at least 3,000 RPMs. You will sharpen many knives be- fore needing to re- surface the grit wheel. The slotted wheel needs to be “ dressed” occasionally with 60 grit sandpaper. PLEASE READ THE INSTRUCTIONS! Including the safety instructions on page four. RECOMMENDED SPEED 3000 - 3600 RPM Page One RAZOR SHARP EDGEMAKING SYSTEM INSTRUCTIONS TO INSTALL WHEELS: You will need to remove the guards from your bench grinder, as they are not needed with this paper wheel. Then in- stall the gritted wheel on the right side of the motor and the slotted wheel on the left side of the motor. Before you turn on the motor, take the conditioning wax ( yellow stuff) out of the cup and rub it sparingly on the black grit wheel until you can see some wax on the grit. Then each time you start to sharpen, just touch the wax to the grit wheel for a second with the motor running. The wax has two functions; a) helps control heat & b) helps the grit stay on the wheel longer. Be careful not to use too much wax, doing so will de- stroy the effectiveness of the grit. There should be streaks of wax ( shiny) on the grit, but if the wax is completely covering the grit it will reduce the grit’s ability to cut into the steel. The slotted wheel needs no pre- conditioning just put it on and whenever you start to use it, simply touch the running wheel with the rouge. This is for heat control as well as for honing & polishing the cutting edge. Do not over- tighten the nuts. Snug is enough. Spin the wheels by hand. If a wheel wobbles from side to side try tap- ping the wheel lightly with your fingers. If you still have a wobble, loosen the nut and turn the washer, or washers, just a little. Turn one washer one way and the other washer the other way. Snug the nut and spin the wheel. You might have to repeat this a time or two to minimize the wobble. A little side to side deviation won’t hurt anything! Sometimes, if a wheel is exposed to heat or dampness, it will warp a little. Place the wheel be- tween two boards, clamp them tightly and keep in a cool dry place for a few hours! Grit Packs containing replacement grit, wax for the gritted wheel and rouge for the slotted wheel can be purchased from ( Item #G5941) . RECOMMENDED SPEED 3000 - 3600 Page Two RAZOR SHARP EDGEMAKING SYSTEM TRUING OF WHEELS: When you have the wheels running “ t...

Download now

Please, enter two numbers from picture: