Votes - 2, Average rating: 4 ( )

Manafacture: Shindaiwa File size: 1.06 mb File name: Language of manual:

WARNING! Before performing any maintenance, repair, or cleaning work on the unit, make sure the engine and cutting attachment are completely stopped. Disconnect the spark plug wire before performing service or maintenance. WARNING! Non-standard accessories, cutting attachment, or replacement parts may not operate properly with your unit and may cause damage and lead to personal injury. NOTE Using non-standard replacement parts could invalidate your Shindaiwa warranty. Daily Maintenance Prior to each work day, perform the following: Remove all dirt and debris from the ¦¦ engine, check the cooling fins and air cleaner for clogging, and clean as necessary. Make sure nuts, bolts, and screws ¦¦ (except carburetor idle speed adjusting screws) are tight. Carefully remove any accumulations ¦¦ of dirt or debris from the muffler and fuel tank. Check cooling air intake area at base of crankcase. Remove all debris. Dirt build-up in these areas can lead to engine overheating, fire, or premature wear. Clean any debris or dirt from the ¦¦ cutting attachment. Check for loose or missing screws ¦¦ or components. Make sure the cutter attachment is securely fastened. Check the entire unit for leaking ¦¦ fuel or grease. 300 Hour Maintenance Gearcase Lubrication The gearcase should be filled with 60 cc (2.0 fl.oz.) of Mobil SHC634 Synthetic Gear Oil. A maximum of 75-80 cc can be used, but never to exceed 80 cc. Operation with excessive oil level will result in high operating temperatures. Do not overfill! Replacing the gearcase oil Disconnect spark plug wire at 1. engine. Remove the LH Drum and axle 2. assembly (as viewed from the operating position). Wipe the sideplate clean and remove four screws (it is not necessary to remove the gearcase from the outer tube). Turn gearcase side plate to break 3. the seal and lift the plate from the gearcase. Turn the gearcase to the LH side 4. and and allow all used gearcase oil to drain into a small container. Place the gearcase on the RH side 5. and supported so the outer tube is parallel to the ground. Refill the gearcase with 60 cc (2.0 fl.oz) of Mobil SHC634 Synthetic Gear Oil to the bottom of the chamfer on the output gear. The correct oil depth is 15.5 mm (5/8"). DO NOT OVERFILL! Inspect the sideplate for damage and 6. clean off all remaining liquid gasket material with brake cleaner or acetone. Coat the outer sealing flange of the sideplate with Loctite Ultragrey Silicon Sealant or Threebond No. 1104 Liquid Gasket. Replace the cover and install the 7. four sideplate screws. Tighten securely. Reinstall the drum and axle assem8. bly per the sweeper assembly instructions. Fill the gearcase to the bottom of the chamfer on the output gear. DO NOT OVERFILL! Turn gearcase side plate to break the seal and lift the plate from the gearcase WARNING! BURN DANGER! The gearcase will be extremely hot after use! NOTE: It may be necessary to use a heat gun to soften the sealer material. Troubleshooting Guide ADDITIONAL PROBLEMS What To Check Possible Cause Remedy Engine idle too high. Check Multipurpose Engine manual for correct idle speed and adjustment procedure. Tines rotates at engine idle. Replace spring/shoes as required, check idle speed. Broken clutch spring or worn clutch spring boss. Inspect and re-tighten holders securely. Loose attachment holder. Warped or damaged attachment. Inspect and replace attachment as required. Excessive vibration. Loose gearcase. Tighten gearcase securely. Bent main shaft/worn or damaged bushings. Inspect and replace as necessary. Shaft not installed in powerhead or gearcase. Inspect and reinstall as required. Tines will not rotate. Broken shaft. Consult with a authorized servicing dealer. Damaged gearcase. SHINDAIWA LIMITED WARRANTY STATEMENT FOR PRODUCT SOLD IN USA AND CANADA BEGINNING 01/01/2010ECHO, INC'S RESPONSIBILITYECHO Incorporated’s (ECHO, INC.) Limited Warranty, provides to the original purchaser that this Shindaiwa product is free from defects in material and workmanship. Under normal use and maintenance from date of purchase, ECHO, INC. agrees to repair or replace at it’s discretion, any defective product free of charge at any authorized Shindaiwa servicing dealer within listed below application time periods, limitations and exclusions. THIS LIMITED WARRANTY IS ONLY APPLICABLE TO SHINDAIWA PRODUCTS SOLD BY AUTHORIZED SHINDAIWA DEALERS. IT IS EXTENDED TO THE ORIGINAL PURCHASER ONLY, AND IS NOT TRANSFERABLE TO SUBSEQUENT OWNERS EXCEPT FOR EMISSION RELATED PARTS. Repair parts and accessories replaced under this warranty are warranted only for the balance of the original unit or accessory warranty period. Any damage caused by improper installation or improper maintenance is not covered by this warranty. All parts or products replaced under warranty become the property of ECHO, INC. This warranty is separate from the Emission control warranty statement supplied with your new product. Please consult the Emission Control Warranty Statement for details regar...

Download now

Please, enter two numbers from picture: