17-1/8 x 14-1/8 in. Shipping Dimensions: Type.............................................................................................................................................................Cardboard Content............................................................................................................................................................Machine Weight...........................................................................................................

508 lbs. Length/Width/Height...........................................................................................................76-3/8 x 23-1/2 x 32-5/8 in. Foot Print (Length/Width).................................................................................................................44-1/2 x 16-1/2 in. Shipping Dimensions: Carton #1 Type..........................................................................................................................................

Loosen the necessary lock knobs (Figure 1), then lower the appropriate dust shield. Figure 1. Model T10115 identification. Cleaning Your table surface may be cleaned with a damp rag. if your table surface gets gummy from wood pitch, you can use a non-corrosive blade cleaner to easily remove it without harming the tabletop surface. DO NOT clean with products such as brake parts cleaner, acetone, or gasoline that will harm the paint on the table surface. To remove sawdust that may become trapp

features • solid oak top (11.2" thick) with double rows of bench dog holes for each vise. • two storage drawers (with ball bearing slides) that are 14" wide x 133.4" long x 21.4" deep. • sturdy adjustable steel legs with leveling foot pads. • two oak-faced vises with removable top plate and 4" leadscrew travel, 13" wide x 2" thick. • Four bench dogs. • all wood surfaces finished with durable lacquer. • overall dimensions: 62" wide x 30" in depth x 32"–39" tall. • Weight: 155 lbs. Inventory use t

.. .. .. .. .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... .... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... ...... .... .... .... .. .. .... .... .... .... .... .... .... .... .... .... .... ...

a nut or a washer), we would be glad to replace them, or for the sake of expediency, replacements can be obtained at your local hardware store. Figure 1. Parts layout. NOTICE A full parts list and breakdown can be found toward the end of this manual. For easier assembly, or to identify specific parts, please refer to the detailed illustrations at the end of the manual. -6-H2854 1 H.P. Variable Speed Plunge Router SECTION 4: ASSEMBLY Beginning Assembly Handles ! Disconnect power to the machine wh

. It was written to guide you through assembly, review safety considerations, and cover general operating procedures. If you have any comments regarding this manual, please write to us at the address below: Grizzly Industrial, Inc. C/O Technical Documentation P.O. Box 2069 Bellingham, WA 98227-2069 Commentary Most importantly, we stand behind our machines. If you have any service questions or parts requests, please call or write us at the location listed below: Grizzly Industrial, Inc. 1203 Lyco

Failure to do this may result in seri- ous personal injury. Regular periodic maintenance on your Model H2801 4" Jointer ensures its optimum performance. Make a habit of inspecting your jointer each time you use it. Check for the following conditions and repair or replace when necessary. 1. Loose mounting bolts. 2. Worn switch. 3. Worn or damaged cords and plugs. 4. Damaged V-belt. 5. Any other condition that could hamper the safe operation of this machine. Table The table and other non-painted s

It is also a necessary step prior to ripping stock to width on a table saw or radial arm saw. 1. Make sure the fence is set to 90°. Double check it now with a try square or machinist’s square. 2. Inspect stock for soundness and grain direction. 3. If the board is bowed (curved), place the concave edge down on the infeed table. 4. Holding the stock firmly against the fence and table, feed the stock slowly and evenly over the cutterhead. See Figure 25. Figure 25. Operator position for edge jointin

Tighten motor mount bolts and recheck tension and pulley alignment. Figure 9. Pulley and V-belt alignment. Bearing Block Cutterhead Setscrews Setscrews Cutterhead Pulley Motor Pulley Fence Place the fence body on the fence support, making sure that it fits over the key. See Figure 10. Insert the locking screw and thread on the special nut provided. The flange on the special nut should protrude upward when installed correctly. Locking Screw Special Nut (Not In Sight) Figure 10. Fence support mech