Votes - 3, Average rating: 3
(
)
)
|
manual abstract
Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine if it will operate properly and perform its intended function. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool's operation. A guard or other part that is damaged should be properly repaired or replaced at a Sears Service Center,. 8. INSPECT and remove all nails from lumber before routing. 9, SAVE THESE INSTRUCTIONS. Refer to them frequently and use them to instruct others who may use this toot. If someone borrows this tool, make sure they have these instructions also. Z_ WARNING: Your router should NEVER be connected to the power source when you are assembling parts, making adjustments, installing or removing collets / nuts, cutter bits, cleaning or when it is not in use. Disconnecting the router will prevent accidental starting, which could cause serious personal injury. When unpacking the box don't discard any packing materials until all of the contents are accounted for: 1_ Carefully lift the Router Motor and Fixed Base with the 1/2-in. collet/nut already installed, out of the carton and place on a stable flat surface. 2. Open the parts bag to locate the following: • Sawdust Extraction Hood and 2 Screws used to attach hood to base • 1/4-in. Collet/Nut • Collet/Nut wrench 3o Inspect the items carefully to make sure that no breakage or damage has occurred during shipping° If any of the items mentioned are missing, (refer to "PARTS LIST" illustration on page 1t), return the router to you r nearest Sears store or Craftsman outlet to have the router replaced° Z_ WARNING: If any parts are broken or missing, DO NOT attempt to plug in the power cord or operate router until the broken or missing parts are replaced. Failure to do so could result in possible serious injury. 10 PARTSLIST (Fig. 1) 1. Fixed Baseand Motor with1/2-in.Collet/Nut (_ 2. Sawdust Extraction Hood 3. 2 Screws _p (for attaching Hood) _p 4. 1/4-in. Collet/Nut 5. Collet/Nut Wrench KNOWYOUR FIXED BASE ROUTER (Fig. 2) I operatingOTE: Before attemptingand safetyto use your router, familiarize yourself with features requirements. all of the Your fixed base router has a precision-built electric motor and it should only be connected to a 120-volt, 60-Hz AC ONLY power supply (normal household current).DO NOT operate on direct current (DC). This large voltage drop will cause a loss of power and the motor will overheat: If the router doesnot_operate when pluggedinto-a correct 120-vott, 60-Hz AC ONLY outlet, check the power supply. This router has an 8-fL, 2-wire power cord (no adapter needed). 11 KNOWYOUR FIXED BASE ROUTER cont. (Fig. 2) This Fixed Base Router has the following features: 1. Powerful, 9.5 Amp Soft Start Motor develops 13/4 Peak HP to handle most routing jobs 2. Single speed 25,000 RPM (no-load speed) helps provide a quality finish in most materials 3. Fixed Base features Coarse and Fine Depth Adjustments for accurate set-upso Ideal for use with router table, sold separately. 4. Spindle Lock for easy !-wrench bit changes_ Includes 1/4-in. and 1/2-in, Self-Releasing Collets/Nuts for use with a wide variety of 1i4-ino and 1/2-in, router bits, sold separately. 5.. 100% Ball Bearings for smooth, efficient operation and long life. 6. Base features Ergonomically Designed Handles for comfort, maximum control. 7_ Base features Large Base Opening and Large Chip Shield, combined with 3 LED Worklights on Motor to provide the highest visibility of bit and workpiece_ 8o Durable Non-marring Sub-base glides smoothty over workpiece. Sub-base has cutter-bit opening of 11/4-inches. Do Not Use a bit with a cutter diameter larger than 11/4-in. as it will not pass through the sub-base opening! 9. Base constructed of Die-Cast Aluminum to provide durability and stability, 10, Motor Housing constructed of High Density Nylon and Precision Milled Cast Aluminum for strength and exact fit into base° 11o High-impact resistant Motor Housing Top Cap and Handles on Base help protect tool from damager 12_ Conveniently located On/OffToggle Switch, side mounted for added visibility, easy access. 13, Sawdust Extraction Hood allows base to hook up to 11/4-inch vac hose attachment, sold separately_. 14. "LIVE TOOL INDICATOR" Light is green when saw is plugged into a power source.. Light is located on motor housing top cap next to power cord inlet, 15o Replaceable Brushes (sold separately) for dependable service. 12 KNOW YOUR FIXED BASE ROUTER cont. (Fig. 2) Motor Housing Dve Tool Top Cap Indicator" Light Motor Housing Milled Cast Aluminum for Exact Fit Fixed Base Quick Clamp Motor Changing Handles System Clear Plastic Chip Shield Spindfe Lock Non-MarringSub-Base Replaceable Brushes Self-Releasing Coltets/Nuts (sold., eparately) System 1/4 and 1/2-inch Cellets/Nuts (1/2-ino installed at factory) On/Off Toggle Switch Motor _ Housing, Keystrip "_. Base Keystrip-SIot (Engages Motor ustment Dial Housing ...