Login:
Votes - 3, Average rating: 4.7 ( )

User manual Grizzly, model G9953

Manafacture: Grizzly
File size: 6.16 mb
File name:
Language of manual:en
Free link for this manual available at the bottom of the page



manual abstract


Remove the RHN-18 overload relay and replace it with a RHN-10 (5.5-8.5A) type, with the dial set to 7A (Figure 4). Figure 4. Overload relays. 7 RHN-10 Overload Relay 4. Remove the CN-18 magnetic contact overload relay and replace it with a CN-11 type (Figure 5). Figure 5. Overload relays. 11 CN-11 Magnetic Contactor Overload Relay 5. Wire the motor as shown on the diagram on the inside of the motor wire cover. Note— The circled references on the diagrams represent labels on the wires. Also, Figure 6 below has been provided for your reference and are current at the time that this manual is being written. However, always use the diagram on the wire cover that comes with your motor! G9953ZXF Motor Wiring 4 5 6 1 2 3 7 8 9 4 5 6 7 8 9 1 2 3 RST RST 220V 440V Figure 6. 440V motor wiring. -10- Ultimate Series Jointers Rewire To 440V (G4815 Only) To rewire the Model G4815 to 440V: 1. Disconnect the sander from the power source! 2. Replace the power indicator light in the pedestal switch to one suitable for 440V operation 3. Remove the RHN-18 overload relay and replace it with a RHN-10 (8.5-12.5A) type, set to 10A (Figure 7). RHN-10 Overload Relay Figure 7. Overload relay. 4. Remove the CN-18 magnetic contact overload relay and replace it with a CN-16 type (Figure 8). Figure 8. Overload relay. CN-16 Magnetic Contactor Overload Relay 5. Wire the motor as shown on the diagram on the inside of the motor wire cover. Note— The circled references on the diagrams represent labels on the wires. Also, Figure 9 below has been provided for your reference and are current at the time that this manual is being written. However, always use the diagram on the wire cover that comes with your motor! G4815 Motor Wiring 4 5 6 1 2 3 7 8 9 4 5 6 7 8 9 1 2 3 RST RST 220V 440V Figure 9. 440V motor wiring. Ultimate Series Jointers -11 SECTION 4: MAIN COMPONENTS 1. Infeed Table: Facing the front of the jointer, the workpiece is lifted from the jointer after the infeed table is located to the right of the the cutting operation is complete. The wood cutterhead. The infeed table is where the travels right to left; from the infeed table, workpiece is placed at the beginning of the across the cutterhead, and onto the outfeed cutting operation. The wood travels right to table. left; from the infeed table, across the cutter- head, and onto the outfeed table. 7. Cutterhead: The cutterhead is the cylindri2. Pedestal Switch: Location of the power indical assembly that holds each of the three jointer knives or indexable carbide cutters. It cator light, the START button, and the spins on a horizontal axis between the EMERGENCY STOP button. infeed and outfeed table, and is covered by 3. Fence Adjustment Handwheel: Controls the cutterhead guard when the jointer is not in use. the back-and-forth location of the fence across the top of the tables. 8. Table Height Handwheels: Controls the 4. Cutterhead Guard: Orange, spring-loaded height positioning of the infeed and outfeed tables in relation to the cutterhead. safety cover that retracts over the cutterhead when the workpiece is NOT passing over the 9. Table Height Lock Knobs: Knobs that jointer. tighten to prevent accidental rotation of the 5. Fence: Surface the workpiece guides along when jointing or surface planing. The fence 10. table height handwheels. Stop Lever: Shuts off the power source to can be positioned 45. and 90. to the surface the jointer and slows the cutterhead to a of the tables to accommodate either bevel or stop. 6. right-angle jointing operations. Outfeed Table: Facing the front of the joint11. Cam Adjustment (Behind Cover): The infeed table is fully adjustable with 4 cams to er, the outfeed table is located to the left of allow perfect alignment with the outfeed the cutterhead. The outfeed table is where table. -12-Ultimate Series Jointers Model G4815 Shown 1 2345 6 7 8 9 11 10 SECTION 5: SET UP Unpacking NOTICE The photos shown in this manual are of the Model G4815 unless otherwise noted. The Model G9953 16" Ultimate Series Jointers and the Model G4815 20" Ultimate Series Jointer are shipped from the manufacturer in a carefully packaged crate. If there are any signs of crate damage after you have signed for delivery, immediately call our customer service for advice. The Ultimate Series Jointers are heavy machines. DO NOT over-exert yourself while unpacking or moving your machine — you will need assis- tance and power equip- ment. Serious personal injury may occur if safe moving methods are not followed. Sharp edges on metal parts may cause person- al injury. Examine the edges of all metal parts before handling. Figure 11. Model G9953 accessories. Ultimate Series Jointers -13 Parts Inventory Models G9953ZX, G9953ZXF, & G4815: Qty • Fence Assembly 1 • Air Pressure Gauge 1 • Air Pressure Regulator 1 • Push Blocks 2 • Air Wrench 1 • T-20 Torx® Screwdriver 5 • Extra Carbide Cutters - 14 x 14 x 2mm 10 • T-Handle For Torx® Bits 1 • Hardware Bag Contents: —Regulator Mounting Bracket 1 —Air ...

Other models in this manual:
Laminate Trimmers - G4815 (6.16 mb)
Laminate Trimmers - G9953ZX (6.16 mb)
Laminate Trimmers - G9953ZXF (6.16 mb)

Reviews



Your review
Your name:
Please, enter two numbers from picture:
capcha





Category