Votes - 3, Average rating: 3.3 ( )

Manafacture: Bosch File size: 1.04 mb File name: Language of manual:

The deluxe router guide is supplied with two rods and screws to fasten the guide (Fig. 27). In addition, it features a fine adjustment knob and indicator for accurately positioning the edge guide relative to the bit. With the guide installed and adjusted, the router should be USE IN ROUTER TABLE Your router can also be used in a router table. The RA1161 fixed base is designed to allow easy depth adjustment in a table. The RA1162 "D" D-Handle base will not fit in most router tables. !CAUTION The RA1166 Plunge Base is not recommended for use in a router table. Damage to plunge router base may occur. To eliminate the hassle of installing your router’s own base on the router table and later having to convert it back for non-table use, Bosch offers the optional RA1165 Undertable Router Base (Fig. 28). The RA1165 base is designed to be permanently attached your router table, leaving your other router bases ready for non-table use. The motor can be quickly moved from base to base — without any tools! fed normally, keeping the guide in contact with the edge of the workpiece at all times. The deluxe router guide may also be positioned directly under the router base for operations where a cut is needed close to or at the edge of the work. The deluxe router guide includes a dust extraction hood and the VAC002 vacuum hose adapter. For complete instructions on installation and operation, please refer to the instructions which are included with this accessory. Shown after subbase has been removed Hole for Hex Wrench Quick-release clamp lever and depth adjustment controls should face the front of the router table Mounting Plate 10-24 Screw FIG. 28 Hex Wrench -21 BM 2610925542 07-06.qxp 7/24/06 12:06 PM Page 22 The undertable base accessory includes the screws needed to fasten the base to a router table mounting plate, as well as the fine adjustment control extension. ATTACHING BASE TO MOUNTING PLATE Attach the RA1161 to the router table’s mounting plate using either or both sets of enclosed mounting screws. The base has two sets of threaded holes for mounting the base: • Three 10-24 holes in industry-standard 3-hole pattern. • Four M4 holes in Bosch 4-hole pattern. Mounting screws required for the RA1161: (not included with all models). • Three 10-24 screws. • Four M4 screws. The length will depend on the thickness of your router table or router table mounting plate. If your router table mounting plate does not have countersunk holes in either of those patterns, you will need to determine the hole locations, drill and countersink them, also locate and drill a hole for the over-table adjustment wrench. CONNECT THE ROUTER AND THE ROUTER TABLE SWITCH To prepare for use of the switch, 1. Make sure the router switch and the router table switch are both turned off. 2. Plug the router table switch cord to wall outlet. 3. Plug the router into the "pigtail" socket on the router table switch. 4. Lock router switch on: squeeze trigger, depress lock-on button, and release trigger. 5. Use the router table switch to start and stop the router. DEPTH ADJUSTMENT (See page 12) FEEDING THE WORKPIECE ON A ROUTER TABLE Always use your router table's fence or starter pin and the appropriate guard and follow the router table's instruction manual. ALWAYS feed the workpiece from right to left across the front of the bit. On Bosch router tables, the correct feed direction is also shown on fence housing and on the featherboards, when they have been properly installed. (Fig. 29) Whenever possible, when using the fence, use a push stick to push the workpiece, especially when working with narrow pieces. For complete instructions on operation of a router in a router table, please refer to the instructions that come with the router table. FIG. 29 WORKPIECE DIRECTION OF FEED BIT BEARING FENCE FACE FENCE FACE TOP VIEW NOTE: For clarity, guard and featherboard removed from drawing. Maintenance Service by a Bosch Factory Service Center or Autho- Preventive maintenance !WARNING rized Bosch Service Station. performed by unauthorized TOOL LUBRICATION personnel may result in misplacing of Your Bosch tool has been properly lubricated internal wires and components which and is ready to use. It is recommended that could cause serious hazard. We tools with gears be regreased with a special recommend that all tool service be performed gear lubricant at every brush change. -22 BM 2610925542 07-06.qxp 7/24/06 12:06 PM Page 23 CARBON BRUSHES The brushes and commutator in your tool have been engineered for many hours of dependable service. To maintain peak efficiency of the motor, we recommend every two to six months the brushes be examined. Only genuine Bosch replacement brushes specially designed for your tool should be used. BEARINGS After about 300-400 hours of operation, or at every second brush change, the bearings should be replaced at Bosch Factory Service Center or Authorized Bosch Service Station. Bearings which become noisy (due to heavy load or very abrasive...

Download now

Please, enter two numbers from picture: