Votes - 1, Average rating: 5 ( )

Manafacture: Harbor Freight Tools File size: 5.29 mb File name: 91130.pdf Language of manual:

Make sure the Nuts are above the mounting holes. Then, screw a Nut (24B) upward on each of the eight Hex Screws to secure the Hex Screws to the Main Table. (See Figure J.) To AttachThe Motor Assembly: 1. Lower the Adjustment Board (17D) with its pre-attached Motor Assembly through the top of the Main Table (20B). Position the Adjustment Board and Motor Assembly so that its Power Cord is on the left hand side and the Spindle Lock Lever (22E) is on the right hand side. Continue lowering the Adjustment Board until it sits on the eight Hex Screws (23B). (See Figures J and K.) ADJUSTMENT BOARD (17D) SPINDLE LOCK LEVER (22E) MOTOR ASSY. MAIN TABLE (20B) .... SCREW (16D) FIGURE K 2. NOTE: The height of the Adjustment Board (17D) can be adjusted by inserting a hex wrench (not included) through the Adjustment Board and adjusting each Hex Screw (23B) individually. Once adjusted, secure the Adjustment Board to the Main Table (20B) with four Screws (16D). (See Figures J and K.) To AttachThe Fence: 1. The Upper Fence (16C) is supplied with sixNuts (11C) already fitted to one channel (groove) of the Upper Fence. The furthest twoNuts on each end of the Upper Fence are for attaching the two Fence Supports (10C) to the Upper Fence. The middle two Nuts are for attaching the Dust Port Box (24C) to the Upper Fence. (See Assembly Diagram C.) SKU 91130 For technical questions, please call 1-800-444-3353. Page 16 2. Position the Upper Fence (16C) on the Main Table (20B). 3. Use two Screws (9C) to attach a Fence Support (10C) to the back of the Upper Fence (16C), making sure to use two of the outermost pre-fitted Nuts (11C) in the channel of the Upper Fence. Do not tighten yet. Repeat this procedure for the remaining Fence Support (See Assembly Diagram C.) 4. Slide the two Fence Supports (10C) along the Upper Fence (16C) until the hole in the horizontal leg of the Fence Supports is above the transverse(right angle) channelat the rear of the Main Table (20B). (See Assembly Diagram C and Figure L.) TRANSVERSE CHANNEL TRANSVERSE CHANNEL MAIN TABLE (20B) FIGURE L 5. NOTE: The screw heads of the Screws (22C) locate in a channel under the Main Table (20B). This channel holds the Screws and prevents the Screws from turning when the Fence Locking Knobs (8C) are tightened or loosened. (See Assembly Diagram C.) 6. Insert the screw head of a Screw (22C) into the channel under the Main Table (20B) so that the threaded portion of the Screw passes through the hole in a Fence Support (10C). Tighten the Screw, using a Fence Lock Knob (8C) and Large Washer (7C). (See Assembly Diagram C.) 7. Tighten the Screws (9C) holding the Fence Support (10C) to the Upper Fence (16C). (See Assembly Diagram C.) 8. Repeat Steps #6 and #7 at the other end of the Upper Fence (16C). To AttachThe Dust Port Assembly And Protector: 1. Position the Dust Port Assembly (26C) and Protector (23C) to the middle of the SKU 91130 For technical questions, please call 1-800-444-3353. Page 17 UPPER FENCE (16C) PROTECTOR (23C) PROTECTOR (23C) rear of the Upper Fence (16C), using the remaining two pre-fitted Nuts (11C) in the channel of the Upper Fence and two Screws (9C). (See Assembly Diagram C and Figure M.) DUST PORT ASSY. (26C) FENCE LOCK KNOB (8C) FIGURE M To Install And Remove Collets: 1. Always make sure the Power Switch (9B) is in its “OFF” position and the Power Cord/Plug (1B) is unplugged from its electrical WARNING! outlet before making any adjustments to the Router Table. 2. The Router is equipped with a 1/4” Collet (18D) and a 1/2” Collet (24D). 3. The Collet (18D, 24D) may need to be changed to allow use of larger or smaller diameter router bits (not included). 4. NOTE: When changing Collets (18D, 24D) or when changing router bits, the height of the Motor Assembly should be raised to the maximum height to gain full access to the Collet Nut (19D). 5. Unlock the Height Adjustment Lock (23D) by rotating it in a counterclockwise direction, using the end of the Wrench (21D) provided. (See Figure N, next page.) 6. Remove the Collet Assembly Cover (15D) by removing the two inner Screws (1D) on the Cover and lifting the Cover away from the Height Adjusting Ring (14D). If necessary, clean off any saw dust and debris which may have built up from previous cutting operations. (See Figure N.) SKU 91130 For technical questions, please call 1-800-444-3353. Page 18 COLLET WRENCH ASSEMBLY (21D) COVER (15D) HEIGHT HEIGHT ADJUSTMENT ADJUSTING LOCK RING (23D) (14D) COLLET COLLET NUT NUT (19D) (19D) WRENCH (21D) FIGURE N 7. Use the Wrench (21D) to turn the Collet Nut (19D) in a counterclockwisedirection while pulling and holding the Spindle Lock Lever (22E) forward. Then, remove the Collet Nut. (See Figures K and N.) 8. Remove the existing Collet (18D, 24D) from the assembly, and make sure to install the correct size Collet (1/4” or 1/2”) for the router bit to be used. Then, finger tighten the Collet Nut (19D) back onto the assembly. (See Figure O.) COLLET (18D, 24D) COLLET NUT (19D) FIG...

Download now

Please, enter two numbers from picture: