Votes - 4, Average rating: 4.5
(
)
)
|
manual abstract
D Fig. D OPERATING INSTRUCTIONS FOREWORD Delta Model 37-380 is a 8" Professional Jointer with a cutting capacity of 8" (203mm) width, 1/8" depth (3mm max.) and 1/2" (13mm) rabbeting. Unit includes; heavy-duty 1-1/2 hp, 120/240 volt induction motor, stand, dust chute, fence, three- knife cutterhead, cutterhead guard, and push blocks. UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY. 6 JOINTER PARTS 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1. Jointer 2. Fence Carriage Assembly 3. Cutterhead Pulley Guard/Carriage Mounting Bracket 4. Table Raising Handle 5. Switch Mounting Bracket 6. Cutterhead Guard 7. Fence Tilting Handles (2) 8. Fence Fig. 2 9. Push Blocks (2) 10. 6mm Hex Wrench 11. 4mm Hex Wrench 12. 3mm Hex Wrench 13. 2.5mm Hex Wrench 14. 12-14mm Open End Wrench 15. 8-10mm Open End Wrench 7 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 34 35 36 33 20 21 22 23 24 25 26 27 28 29 30 31 32 34 35 36 33 Fig. 3 16. Stand with Pre-Wired Switch 17. Dust Chute 18. V-Belt 19. Pulley 20. 3/8-16x2" Hex Head Screw (3) 21. M8x1.25x55mm Hex Socket Head Screw (4) 22. M8x1.25x25mm Hex Socket Head Screw (2) 23. M8x1.25x20mm Hex Socket Head Screw (2) 24. M8x1.25x16mm Hex Socket Head Screw (2) 25. 5/16-18x1" Hex Head Screw (1) 26. #10-16x1/2" Sheet Metal Screw (4) 27. 3/8" Flat Washer (6) 28. 11/32" Flat Washer (1) 29. M8 Flat Washer (10) 30. 3/8" Lockwasher (3) 31. M8.1 Lockwasher (10) 32. 5/16" Lockwasher (1) 33. M14x2 Hex Nut (1) 34. 3/8-16" Hex Nut (3) 35. 5/16-18 Hex Nut (1) 36. Key ASSEMBLY FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE INSTRUCTION MANUAL. JOINTER TO STAND Your Jointer stand (A) Fig. 4, is shipped with the motor and switch completely wired. NOTE: THE MOTOR IS BOLTED TO THE TOP OF THE STAND AND MUST BE ATTACHED TO THE MOTOR MOUNTING BRACKETS. 1. Remove the six screws (C) Fig. 4. Then remove back panel (E) from the stand. C C E Fig. 4 8 2. Remove the four bolts that attach the motor (A) Fig. 5 to top of the stand. NOTE: SAVE THESE BOLTS AS THEY WILL BE USED TO ATTACH THE MOTOR TO THE MOUNTING BRACKETS. 3. Align the holes in the motor mounting plate (B) Fig. 5A with the four holes in the two motor mounting brackets (C). Attach the motor to the motor mounting brackets with the hardware that was removed in STEP 2. NOTE: MAKE SURE THAT MOTOR SHAFT (D) FIG 5A IS FACING OUT OF THE OPENING IN THE MOTOR CABINET AS SHOWN. 4. Turn the stand over so that it is resting on its base as shown in Fig. 6. A Fig. 5 THE JOINTER IS EXTREMELY HEAVY. HAVE TWO OR MORE PEOPLE LIFT THE MACHINE ONTO THE STAND OR LIFT THE JOINTER MECHANICALLY. 5. Line up three holes (F) and (L) Fig. 6, on top of stand with three holes located at the bottom of the jointer base. Place a 3/8" flat washer (H) Fig. 7, on a 3/8-16x2" hex head screw (G), insert the screw through the hole in the base of the Jointer and hole (F) Fig. 6, in the stand. Place a 3/8" flat washer (H) Fig. 7, 3/8" lockwasher (J), and thread a 3/8-16 hex nut (K) onto the screw and tighten securely. Repeat this process for the remaining hole (F) in the stand and Jointer base. Repeat this process for hole (L) in the stand and Jointer base by inserting the screw up through hole (L) in the stand and the Jointer base. ASSEMBLING INFEED TABLE ADJUSTMENT HANDLE 1. Thread an M14x2 hex nut (A) Fig. 8, clockwise onto the end of adjustment handle (B) as far as it will go. 2. Thread handle (B) Fig. 8, into block (C) which is located under infeed table (D). Tighten hex nut (A) Fig. 8, against block (C). B C D Fig. 5A F L Fig. 6 G H J K D B A C Fig. 7 Fig. 8 9 ASSEMBLING MOTOR PULLEY Assemble motor pulley (K) Fig. 10, to motor shaft with the hub of the pulley in the outer position as shown. Make certain key (L) is inserted in the keyway of the pulley and motor shaft, then tighten set screw (M) using the 3 mm hex wrench (not shown). K L M Fig. 10 ASSEMBLING BELT AND ALIGNING PULLEYS 1. Place belt (A) Fig. 11, in groove of cutterhead pulley (B) and motor pulley (C). 2. Make certain the motor pulley (C) Figs. 11 and 12, is properly aligned with cutterhead pulley (B) by placing a straight edge (D) Fig. 12, onto the face of each pulley as shown. 3. If an adjustment is needed, the motor pulley can be moved in or out on the motor shaft, or the motor can be shifted by loosening motor mounting screws, two of which are shown at (E) Fig. 12. ...